215777

Sanyo plc xl51 Manual

66
Zoom out
Zoom in
Previous page
1/77
Next page
66
Appendix
Image is out of focus.
– Adjust focus of the projector (see page 24).
– Provide proper distance between the projector and the projection screen
(see page 14).
– Check the projection window to see if it needs cleaning (see page 62).
– Moving the projector from a cool to warm place may result in moisture
condensation on the projection lens. If this occurs, leave the projector off
and wait until condensation evaporates.
– Projecting from excessive slant angle to the screen may cause keystone
distortion and partial imperfect focus.
Picture is not bright enough.
– Check if “Contrast” or “Brightness” are adjusted properly. (See page 34,
42)
– Check if “Image level” is selected properly. (See pages 32-33, 40-41)
– Check the Lamp control function. ( See “SETTING” section on page 51)
– Check the Lamp replace indicator. If it lights, the end of lamp life is
approaching. Replace the lamp with a new one promptly. (See page 63)
The color is strange.
– Check the Input signal, color system, video system, or computer system
mode.
– Adjust the Image Level properly. See pages 32-33, 40-41.
Image is Left/Right reversed.
Image is Top/Bottom reversed
– Check the Ceiling/Rear function (see page 49).
– Check the Ceiling function (see page 49).
The image is distorted or runs off.
– Check “PC Adjustment” menu or “Screen” menu and adjust them.
No sound
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button (see page 25).
– Press the Mute button (see page 25).
– Is the image projected? You will hear the sound only when the
image is projected.
– When the AUDIO OUT is plugged in, the projector’s built-in speaker is not
available.
Auto PC adjustment function does
not work.
– Check the Input signal. Auto PC Adjustment function can not work when
480p, 575p, 720p, 480i, 575i, 1035i, or 1080i is selected. (See page 29)
Some displays are not seen during
the operation.
– Check the Display function (see page 46).
The setting does not remain after
turning off power.
– Make sure you selected “Store” after adjusting settings. Some settings
can not be stored if not registered with “Store”.
Power management function does
not work.
– Power management function can not work while “Freeze” or “No Show”
function is running.
Image disappears automatically.
– Check the power management function in the Setting. The power
management is set to "On" at the factory.
Capture function does not work.
– Check the connection and input signal to see if there is signal.
… 66 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo plc xl51 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo plc xl51 in the language / languages: English as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info