215777
65
Zoom out
Zoom in
Previous page
1/77
Next page
65
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
Make sure you have properly connected the projector to peripheral equipment as described on pages 16-18.
Make sure all equipment is connected to the AC outlet and the power is turned on.
When you operate the projector with a computer and it does not project an image, restart the computer.
Appendix
Problem:
Solutions
No power
Plug the power cord of the projector into the AC outlet.
See if the POWER indicator lights red.
Wait until the POWER indicator stops blinking to turn on the projector
again. The projector can be turned on after the POWER indicator turns red.
(see page 21).
Check the WARNING indicator. If the WARNING indicator lights red, the
projector cannot be turned on (see on page 60).
Check the projection lamp (see page 63).
Check if the projector is installed in proper position. (See page 7)
Unlock the Key lock function for the projector. See page 51.
PIN code dialog box appears at
start-up.
PIN code lock is being set. Enter a PIN code; the “1234” or numbers you
have set (see pages 20, 52-53)
The initial display is not shown.
Make sure “Off or “Countdown Offare not chosen at Display function.
(See “SETTING” section on page 46)
The initial display is not same with
the default one.
Make sure “User” or Offare not chosen at Logo select function. (See
“SETTING” section on page 47)
Input signal switches automatically.
(or does not switch automatically)
Make sure Input search function is adjusted properly. See page 49.
When the projector is on and you
press the input button, an icon other
than the Lamp mode icon appears.
That is the Filter warning icon. Refer to page 55.
An icon other than Input mode or
Lamp mode icon appears.
That is the Lamp replacement icon or the Filter warning icon. See page
54.
No image
Check the connection between your computer or video equipment and the
projector (see pages 16-18).
See if the input signal is correctly output from your computer. Some laptop
computers may need to be changed the setting for monitor output when
connected to the projector. See your computers instruction manual for the
setting.
It takes about 30 seconds to display an image after turning on the
projector.
See if the selected system is corresponding with your computer or video
equipment (see pages 28, 39).
Select correct input source once again through menu operation (see pages
27, 37–38).
Make sure the temperature is not out of the specified operating
temperature (41 ˚F–104 ˚F [5 ˚C–40 ˚C]).
When "No Show" is operating, the image can not be displayed. Press the
NO SHOW button or any other button on the remote control.
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo plc xl51 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo plc xl51 in the language / languages: English as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info