489561
108
Zoom out
Zoom in
Previous page
1/135
Next page
6. Maintenance
99
Replacing the Lamps
When a lamp reaches the end of it’s usable life, the following message is displayed. Replace the lamp.
The projection lamps should be replaced when they burn out. They should only be replaced with a certified replacement
part, contact your local dealer if unsure.
Note:
1. Lamps are positioned differently. Take care not to force the lamps when replacing.
2. Installation of both lamp modules (Lamp 1 and Lamp 2) is required to operate the projector in dual or sin-
gle lamp mode. If only a single lamp module is installed, the projector's lamp will not turn on and will appear
as a lamp failure.
3. Lamps last approximately 2000-2100 hours (2500-2600 hours in Eco mode) and the End of lamp life
message is displayed during the lamps' final 100 hours of operational life. Please replace during 2000-2100
hour.
Important:
1. The lamp contains a certain amount of mercury and should be disposed of according to local ordinance
regulations.
2. Avoid touching the glass surface of the new lamp: doing so may shorten its operation life.
CAUTION
Lamp Handling Precautions
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling
may result in accidents, injury, or create a fire hazard.
Lamp life may differ from lamp to lamp and according to the environment of use. There is no guar-
antee of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period
of time than other similar lamps.
If the projector indicates that the lamp should be replaced, i.e., if LAMP 1 and/or LAMP 2 light up,
replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow care-
fully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp
with LAMP 1 and/or LAMP 2 lighted may increase the risk of lamp explosion.
A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as
its lifetime draws to an end. Risk of explosion may differ according to the environment or condi-
tions in which the projector and lamp are being used.
If a lamps explodes, the following safety precautions should be taken:
Disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station
for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are
no broken shards or pieces of glass around the projector or coming out from the cooling air circulation
holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the pro-
jector except those who are authorized trained technicians and who are familiar with projector service.
Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to
do so, may result in an accident or injury caused by pieces of broken glass.
108


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PDG-DXT10KL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PDG-DXT10KL in the language / languages: English as an attachment in your email.

The manual is 8,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo PDG-DXT10KL

Sanyo PDG-DXT10KL User Manual - German - 135 pages

Sanyo PDG-DXT10KL User Manual - Dutch - 110 pages

Sanyo PDG-DXT10KL User Manual - French - 135 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info