30744
9
Zoom out
Zoom in
Previous page
1/44
Next page
2
2
1
1
Turn on the TV and set it
to channel 3.
If channel 3 is already occupied for broadcasting,
see“RF Output Channel” section.
Preset for Use
9
EN
Setup
VCRVCR DVDDVD
OUTPUT
POWERPOWER
VIDEOVIDEO AUDIOAUDIO
AV INPAV INPUT
REWREW F.F
W
D
STOPSTOP/EJECTJECT
PLAY
RECREC
TIMER RECTIMER REC
RECREC/OTROTR
CHANNELCHANNEL
OPENOPEN/CLOSECLOSE
VCRVCR DVDDVD
PROGRESSIVEPROGRESSIVE
OUTPUTOUTPUT SKIPSKIP/REVREV STOPSTOP PLAYPLAY F WDWD/SKIPSKIP
OUTPUT button
DVD OUTPUT
light
VCR OUTPUT
light
DVD
button
VCR
button
STOP
PLAY
123
456
789
0 +10
POWER
SPEED
AUDI O
DISPLAY
SLOW
PAUSE
ENTER
MENU
TOP MENU
SETUP
MODE V.SURR
SEARCH
MODE
A
-
B
REPEAT
ANGLE
SUBTITLE
T- SET
DVD
REC OTR
VCR TV
SKIP CH.
CLEAR
C.RESET
VCR
RETURN
Pressing the OUTPUT button on the front panel
switches the output signal. (The VCR or DVD
OUTPUT light is lit.)
However, when using the remote control, you
must press the DVD or VCR button on the
remote control first.
To use the VCR, press the VCR button on the
remote control.
(Verify that the VCR OUTPUT light is lit.)
To use the DVD player, press the DVD button
on the remote control.
(Verify that the DVD OUTPUT light is lit.)
Note
This remote control cannot operate your TV.
POWER
POWER
VIDEO
VIDEO
AUDIO
AUDIO
AV INP
V INP
UT
REW
REW
F.F
W
D
STOP
STOP
/EJECT
JECT
PLAY
REC
REC
TIMER REC
TIMER REC
REC
REC
/OTR
OTR
CHANNEL
CHANNEL
OPEN
OPEN
/CLOSE
CLOSE
VCR
VCR
DVD
DVD
PROGRESSIVE
PROGRESSIVE
OUTPUT
OUTPUT
SKIP
SKIP
/REV
REV
STOP
STOP
PLA
PLA
Y F WD
WD
/SKIP
SKIP
VCR/DVD Switching
Front Panel Display
Lights up when
the inserted disc
is being played
back.
Flashes when an
unacceptable disc
is installed.
Lights up when the timer recording
or an OTR recording has been set.
Lights up during a recording.
Flashes when a recording is paused.
Lights up when the progressive scan
system is activated.
Need help? Call
1-800-813-3435
Lights up when power is on.
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
Hint
Hint
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
POWER
3
3
CH 01
AUTO SET UP
No
No
Please wait for a few minutes.
After scanning...
The tuner stops on the lowest memorized
channel.
•You can select only the channels memo-
rized in this unit by using the CHANNEL
buttons.
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press the
B button once again.
Y
Y
es
es Press the MENU
button to exit.
• Refer to “Hint for Cable Box
or Satellite Box” section on
page 6.
Do you connect the cable from the cable box or
the satellite box to the DVD+VCR’s ANT-IN jack?
YES
NO
Turn on the unit for the first
time
TV ScreenRemote Control
VCRVCR
VCR
VCR
Press the VCR button first.
or
TIP:
If you change the on-screen language at
step [2], change the language for DVD func-
tion in “PLAYER MENU” setting. (Refer to
page 20.)
H9680UD_EN/SP.qx3 04.8.10 4:26 PM Page 9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo DVW7100A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo DVW7100A in the language / languages: English, Spanish as an attachment in your email.

The manual is 3,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info