Manual Sanibroyeur SANICOM 1 Expert-line (page 7 of 32) (All languages)

532741

Zoom out

Zoom in

1/32

ALARM

There is the option of connecting an alarm (light, bell) on to

the electronic circuit board (2 terminals fed with 220V). If the

motor is fed continuously (more than 5 minutes), the contact

will be made. This enables the user to carry out a check if he

wishes.

CONNECTION OF THE ALARM

Two 6.35 push on connection points are available on the

electronic circuit board (arrowed) for creating an alarm

circuit. (These connectors have a 220V, 0.5A maximum

current passing through them). To access them after turning

the power off, remove the cover then unscrew and unclip

the upper casing of the electronic box, to expose the

electronic circuit board. On this card use the point marked

E.V. and the unused neutral connection point marked N.

Use a round 2 x 0.75 mm2 wire, which must pass across

the lid of the upper casing, through the cable gland, before

being connected to the chosen alarm system.

USE

SANICOM

1 is designed for disposing of wastewater

originating from sinks, clothes washing machines,

dishwashers, showers or baths and basins.

SANICOM

1 can pump out hot water.

CAUTION:

1. Do not dispose of concentrated chemical products (acids,

solvents, bases, oxidants, reducers, etc.) into sanitary

ware connected to the SANICOM

2. In the event of power failure, stop all water flow to the

appliances connected to the SANICOM

WARRANTY

SANICOM

1 SFA is guaranteed for 2 years for labour and

parts, subject to correct installation and use of the

apparatus.

STANDARD

This piece of equipment complies with the EN 12050-2 stan-

dard (Lift station for effluents not containing faecal matter) and

the directives and European standards on electric safety and

electromagnetic compatibility.

ELECTRICAL INSTALLATION MUST BE CARRIED OUT BY A

PROFESSIONAL ELECTRICIAN

COMMISSIONING

Once the hydraulic and electrical connections have been

made, check that the connections are tight by allowing water

to flow through each entry point used. Ensure that the pump

is working properly.

FIRST LEVEL TROUBLESHOOTING

REMEDY

1. Check the electrical installation.

1. Vérifier l’arrivée d’eau, sinon

voir ci-dessous

PROBABLE CAUSE

1. The appliance is not switched on

2. The cable is defective

1. Pump blocked

2. Pump jammed

3. Too much water flowing

through

PROBLEMS

• Motor does not start

• The alarm sounds

For all other intervention, disconnect the electrical current.

PROBLEM ENCOUNTERED

• Motor does not start

• Pumps working constantly

• Alarm sounding

• Intermittent start-up of pumps

PROBABLE CAUSE

1. Pressure reader tube kinked or

out of position

2. Electronic card defective

1. Level pressure pipe is blocked

2. Vertical discharge too high

3. Electronic card defective

1. Pump blocked

2. Pump jammed

3 Electrical problems with motor

4. Too much water flowing

through

5. Electronic card defective

1. The non-return valve broken

or leaking

2. Electronic card defective

REMEDY

1. Remove or replace the tube.

2. Consult an SFA-approved

breakdown technician.

1. Extract the level pressure pipe

unblock it.

2. Examine the appliance.

3. Consult an SFA-approved

breakdown technician.

1. IAdjust the pump which is

displaying the alarm:

• Using a screwdriver, turn the

motor shaft by accessing it

through the hood.

• Remove the pump and

unblock it.

If the pump revolves but does not

pump, consult an SFA-approved

breakdown technician.

5. Consult an SFA-approved

breakdown technician.

1. Clean or change the valve.

2. Consult an SFA-approved

breakdown technician.

SECONDARY TROUBLESHOOTING

ELECTRICAL INSTALLATION MUST BE CARRIED

OUT BY A PROFESSIONAL ELECTRICIAN

REMOVAL

13a

REMOVING THE MOTOR

SWITCH THE APPLIANCE OFF (the yellow indicator light

must be out).

Empty the tank.

To access the anti-backflow valve:

Unscrew the clips and then remove the elbow (6).

Clean or replace the valve (8).

To remove the motor

Unscrew the six screws (66) torx T20.

Turn the motor anti-clockwise (warning: the motor may

be hot) and lift it out.

13b

REPLACING THE MOTOR

Locate the motor into the adaptor plate, ensure it is firmly

home and turn it clockwise until the reference marks line

up.

Screw in the six screws into the adaptor plate.

Check that the motor can turn freely using a screwdriver

into the top of the motor shaft.

ELECTRICAL INSTALLATION MUST BE CARRIED

OUT BY A PROFESSIONAL ELECTRICIAN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sanibroyeur SANICOM 1 Expert-line in the language / languages: All languages as an attachment in your email.

The manual is 4,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanibroyeur SANICOM 1 Expert-line

Sanibroyeur SANICOM 1 Expert-line Additional guide - Dutch - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sanibroyeur SANICOM 1 Expert-line Manual

Product: