Manual Sanibroyeur SANICOM 1 Expert-line (page 6 of 32) (All languages)

532741

Zoom out

Zoom in

1/32

WARNING NOTICE

SANICOM

1 is a lifting pump for wastewater used in com-

mercial applications (restaurants, hairdressing salons, the

catering industry etc.). The unit operates automatically, has

a high performance level, and is safe and reliable, provided

all the rules for installation and maintenance in this notice

are strictly followed.

Especially those indicated by:

» Failure to comply with this instruction could endanger

the safety of persons,

» Indication that a risk of electrical

origin exists,

» Electrical installation must be carried out by a

professional electrician.

«ATTENTION» Failure to comply with this instruction could

endanger the safe functioning of the apparatus.

For any additional information, please contact our customer

service department.

HOW IT WORKS

SANICOM

1 contains 1 pump. The tank is equipped with a

sensor tube which controls the automatic activation of the

motor when waste enters the unit.

As soon as the waste enters the tank, the pump starts.

LIST OF PARTS SUPPLIED

DIMENSIONS

SANICOM

1 TECHNICAL DATA AND APPLICATION

Application

Sinks, washing machine,

dishwasher or shower*

or bath*

Type P100

Maximum vertical pumping height 10 m

Voltage 220 – 240 V

Frequency 50 Hz

Maximum power consumption 1300 W

Maximum current consumption 6 A

Electrical class I

Protection index IP44

Max temp with intermittent functioning 90°

Net weight 10 kg

* In the case of bath or shower tray, make sure the waste

traps are raised 19 cm above floor level.

CAUTION: 1. All applications other than those described in

this notice are prohibited.

2. Do not exceed an incoming flow rate greater

than 80% of the flow rate stated on the design

curve

in any of the apparatus.

PERFORMANCE CURVES

VERTICAL/HORIZONTAL PUMPING

INSTALLATION

The pump has securing devices, preventing it from turning

or moving.

FITTING

1- Warning: The space in which SANICOM

1 is installed must

be large enough to leave at least 600mm around the unit

for easy maintenance. This space must be well lit, ventila-

ted, and must never be immersed in water and must be

protected from frost.

2- Isolation valves should be fitted to the inlet pipework and

discharge pipework to isolate the unit in case of the need

for service.

3- This evacuation pipe must be designed so as to prevent

back-flow from the sewers.

CONNECTION TO SIDE INLETS

Use the flexible inlet connector

for side input connections.

Using a metalwork saw, saw

the desired input point, remove any burrs and then fix the

flexible inlet connector with the jubilee clip

CAUTION: In the case of an installation for drainage of

greasy wastes allow for a grease trap in front of each input

point.

Connection to the inlet can be made using a DN40

or DN50 pipe. To make a DN50 connection, cut off the end

of sleeve

beforehand.

CONNECTION TO SANITARY WARE

To connect bathtub (or shower), make sure the waste

trap height is raised by at least 19 cm above floor level.

Connection must be made using 40 mm or 50 mm diameter

pipework, with minimum slope of 1%.

CONNECTION TO SOIL AND VENT PIPE OR DRAIN

The disposal of waste from the SANICOM

can discharged

through a 32 mm diameter copper or plastic pipes (or PVC,

ABS, etc.).

Horizontal discharge pipework should maintain a 1% fall

(1cm/M) to the soil and vent pipe. If a vertical rise is

required, this must be installed at the start of the run,

before the horizontal section.

Take care that the discharge valve flap faces the direc-

tion of flow.

If the end of the discharge pipework is much lower than the

unit, install a riser pipe about 80mm long from the highest

point of the discharge run and fit an air admittance pipe on

top (capable of withstanding at least 15psi pressure.) to

break the syphon.

End the outlet pipe at the waste stack.

PLEASE NOTE: be sure to fit hoop

IN CASE SERVICE IS NEEDED

Allow for a drain-off point at the bottom of the rising

waste pipe. Ensure that the unit is easily accessible for pos-

sible maintenance.

ELECTRICAL CONNECTION

The electrical installation should be carried by a qualified

person.

All wiring must conform to BS7671, 1992 requirements for

electrical installation. The unit requires a 220/240 V single

phase AC 50 Hz supply (UK specification). Do not connect

the unit to a conventional plug and socket. The unit should be

connected to a fully earthed electrical supply (class 1). It must

be wired into an unswitched fused fixed wiring connector

protected by a 10 amp fuse and a residual current detector

(30 mA). This connection must be used exclusively for

supplying the SANICOM

1 unit.

The wires in the mains lead are coloured in accordance with

the following code:

Brown - Live

Blue - Neutral

Green/Yellow - Earth

WARNING: Ensure the electricity is turned OFF at the main

switch board before wiring to connector. All work on cable,

pressure chamber and motor should only be carried out by a

qualified SANIFLO servicing agent, as special tools are

required.

CAUTION: When the apparatus is connected up for the first

time, it will work for 5 seconds even if there is no water in

the basin. This operation acts as a manual start-up.

Fully illustrated step by step instructions are

downloadable on www.saniflo.co.uk

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sanibroyeur SANICOM 1 Expert-line in the language / languages: All languages as an attachment in your email.

The manual is 4,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanibroyeur SANICOM 1 Expert-line

Sanibroyeur SANICOM 1 Expert-line Additional guide - Dutch - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sanibroyeur SANICOM 1 Expert-line Manual

Product: