797031
6
Zoom out
Zoom in
Previous page
1/21
Next page
5
Using the radio for the
f
i
rst time
1. Place your radio on a
f
l
at surface.
2. Insert the adaptor plug into the DC socket located on the rear of
your radio. Plug the adaptor into a standard AC outlet. If no time is
displayed, the screen will show “--:- - -- ”.
3. Fully extend the FM telescopic antenna located on the rear of your
radio.
4. Press and release the Standby button to turn on your radio. It may
be necessary to relocate your radio to a position giving better
reception and carry out a scan to
f
i
nd stations as described in
later sections.
IMPORTANT:
The AC adaptor is used as the means of connecting the radio to
your power supply. The AC Adapter used for the radio must remain
accessible during normal use. In order to disconnect the radio from
the power completely. The AC Adapter should be removed from the
main power completely in case of severe lightning or storm.
Antenna setup for AM reception
The radio comes with a built-in AM Ferrite antenna which should be
enough for normal listening.
To improve the AM reception, first try to rotate the unit 90 degrees,
if this doesn't help you may connect an external AM antenna (not
supplied) to the AM external antenna terminal on the back of your radio.
Operating your radio – FM/AM auto-tune
1. Fully extend the FM telescopic antenna located on the rear of your
radio.
2. Press and release the Standby button to switch on your radio.
3. Press the Source button repeatedly to select the desired frequency
band.
4. If this is the first time searching for an FM/AM station, press and
release the Tuning control knob, the radio will search from low
frequency to high frequency and stop automatically when it
f
i
nds a
station of suf
f
i
cient strength.
5. For scanning stations backwards quickly, rotate the Tuning control
knob in an anticlockwise direction rst, and then press and release
it. Your radio will scan down the FM/AM frequency band from the
currently displayed frequency and will stop scanning when it finds
a signal of sufficient strength. To scan up in frequency, rotate the
Tuning control knob in a clockwise direction. The displayed frequency
will increase. Then press and release the Tuning control knob to
carry out auto-tune. Your radio will scan up the FM/AM frequency
band from the currently displayed frequency and will stop scanning
when it nds a station of sufcient strength.
6. After a few seconds the display will update. The display will show the
frequency of the signal found. If the signal is strong enough and there
is RBDS data present then the radio may display the station name.
7. To
f
i
nd other stations press the Tuning control knob as before.
When the end of the frequency band is reached, your radio will
recommence tuning from the opposite end of the frequency band.
8. Adjust the Volume to the required setting.
9. To switch off your radio, press and release the Standby button. The
display will show the “OFF” symbol.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sangean WR-50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sangean WR-50 in the language / languages: English as an attachment in your email.

The manual is 1.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info