567084
11
Zoom out
Zoom in
Previous page
1/14
Next page
Simply pressing one button. To program the Direct button recall your favorite station, press MEMO
button (16) [M] and then press PRIORITY button (13) [ ].
ALARM FUNCTION
The ATS-909 has three timer circuits as indicated by TIMER button (6) [1] [2] [3]. The alarm function
may be set with the power on or off. To set the alarm tune to the station you would like to be awaken to.
Press MEMO button [16]. Press one of the three timer buttons (6) [1] [2] [3]. The timer and button
number will flash in the LCD display along with the icon indicating radio or buzzer for approximately 12
seconds. Select radio or buzzer by pressing MODE button (7). While flashing continues set time or
alarm to come on using the numerical keys (19) on the key pad. When complete press ENTER key (17).
Repeat steps for other timers.
In addition to being able to set 3 different wake up times it is possible to set each wake up time to a
different frequency.
SETTING THE SLEEP TIMER (AUTO SHUT-OFF)
The sleep timer allows the user to set the auto-shut off in 10 minutes decrements from 90 minutes to 10
minutes. To set auto shut-off press POWER/SLEEP button [1] and hold down. The display will show a
bed symbol and a series of switch off times descending in time as long as the POWER/SLEEP button is
depressed. Release button when shut off time desired is reached. Radio will remain on for selected
length of time.
RDS FUNCTION
The ATS-909 incorporates circuitry to receive FM stations transmitting an RDS (Radio Data System)
signal. When receiving an RDS station the display will show the station call letters and if the RDS
station is also transmitting a CT function (clock time) it will automatically correct the time every minute. It
is important to make sure that the Home Time (as described under "SETTING THE CLOCK (REAL
TIME)" is set correctly. In addition if your time zone is operating under Daylight Savings Time make sure
the DST (Daylight Savings Time) button [2] is depressed. For the time function to operate the following
conditions must exist:
a: TIME SET switch button (32) must be set in the AUTO position.
b: Radio must be on.
c: Radio must be tuned to an FM station transmitting RDS CT function.
SINGLE SIDE BAND (SSB) RECEPTION
SSB is very popular among ham and business radio users because of its signal intelligibility superiority.
Many amateurs who operate SSB and transmit below 10 MH generally use the lower side band (LSB)
while amateur and commercial stations transmitting above 10 MH generally use the USB. Your ATS-
909 is equipped to receive all USB and LSB transmissions. To receive SSB stations:
1] Turn the set on.
2] Extend the telescoping antenna full length and position upright or use external antenna.
3] Set the RF Gain Control [25] to maximum.
4] Select the SW band as described in "SELECTING A SW BAND"
5] If frequency of SSB station sought is known enter the frequency in accordance with earlier
z
z
10
1
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sangean ATS-909 W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sangean ATS-909 W in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info