651717
77
Zoom out
Zoom in
Previous page
1/94
Next page
Issues Solutions and Explanations
There is no picture/video. Check the cable connections. Remove and reconnect all cables connected to the
product and external devices.
Set the video outputs of your external devices (Cable/Sat Box, DVD, Blu-ray etc) to
match the product's input connections. For example, if an external device’s output is
HDMI, it should be connected to an HDMI input on the product.
Make sure your connected devices are powered on.
Be sure to select the correct input source.
Reboot the connected device by unplugging it, and then reconnecting the device’s
power cable.
The remote control does not
work.
Replace the remote control batteries. Make sure the batteries are installed with their
poles (+/–) in the correct direction.
Clean the sensor’s transmission window on the remote.
Try pointing the remote directly at the product from 1.5~1.8 m away.
The cable/set top box remote
control doesn’t turn the
product on or off, or adjust
the volume.
Programme the Cable/Set remote control to operate the product. Refer to the Cable/
Set-Top-Box user manual for the SAMSUNG product code.
Anynet+ (HDMI-CEC)
Anynet+ does not work. Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+
devices only.
You can connect only one receiver (home theatre).
Check if the Anynet+ device power cord is properly connected.
Check the Anynet+ device’s Video/Audio/HDMI cable connections.
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
Check whether the product remote control is in product mode.
Check whether the remote control is Anynet+ compatible.
Anynet+ doesn’t work in certain situations. (Searching channels, operating Setup,
etc.)
If you have removed and then reconnected the HDMI cable, please make sure to
search devices again or turn your product off and on again.
I want to start Anynet+. Check if the Anynet+ device is properly connected to the product and check if the
Anynet+ (HDMI-CEC) is set to On. (System Anynet+ (HDMI-CEC))
Open the Tools menu using your remote and then select Anynet+ (HDMI-CEC). Then
select a menu you want.
I want to exit Anynet+. Select View TV in the Anynet+ menu.
Go to Source screen using your remote and select a non-Anynet+ device.
The message Connecting to
Anynet+ device ... appears on
the screen.
You cannot use the remote control when you are configuring Anynet+ or switching to
a view mode.
Use the remote control after the product has completed Anynet+ configuration or
has finished switching to Anynet+.
English - 77
Other Information
77


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samsung V27F390FE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samsung V27F390FE in the language / languages: English as an attachment in your email.

The manual is 12,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info