621339

Samsung SCB-9051 Manual

7
Zoom out
Zoom in
Previous page
1/19
Next page
Thermal Night Vision Camera User Guide
12
Thermal Night Vision Camera User Guide
13
Inputting Power
Startup
Connect the video output terminal on the rear of this product to the monitor.
■Connecting the Monitor
IR camera
Intermediate video receiver
End equipment
* Deviations may occur depending on the type of power cable shown in the chart above, and on the
wiring manufacturer.
When the resistance value of copper wire is at [20°C(68°F)]
Copper wire size (AWG)
#24(0.22
2
) #22(0.33
2
) #20(0.52
2
) #18(0.83
2
)
Resistance (Ω/m)
0.078 0.050 0.030 0.018
Voltage Drop (V/m)
0.028 0.018 0.011 0.006
•Thisdeviceisnotfittedwithapowerswitch.Thedevice
must be provided with power to turn it
•Aftercheckingthelabelonthecableontherightsideof
the camera, connect the output cable of the provided
adapter.
•Refertotheowner’smanualforeachdevice.Connectionmethodsemployedmaydiffer
depending on the monitors and peripheral devices used.
•Beforeconnectingdevices,ensuretheirpoweristurnedoff.
•Adjustthe75Ω/Hi-Zconversionswitchforeachdevicebasedonthefollowing
illustration.Select“Hi-Z”forintermediatevideoreceiversand“75Ω”forendequipment.
Calibration (NUC MODE)
Monitor/Communications Connection
Installing the Camera
1. Remove the lens cap.
2. Engage the power. (Use the adapter provided with this product.)
3.TheratedinputvoltageforthisproductisAC24V,50/60Hz.
1.TheSTARTscreenwillappearafterthepowerhasbeenturnedon.
2. After completion of initialization, thermal images will be displayed. (approx. ten seconds
after engaging the power)
Thisdevicewillperformacalibrationnecessaryforimaging(NUC)aftertheinternalshutter
closes.
During NUC, the screen will freeze momentarily. Please note that this is not a malfunction.
Thesensorwillnotoperateproperlyimmediatelyafterthepoweristurnedon,orwhenswitching
between HIGH and LOW ranges. As a result, thermal images will not display consistently for several
seconds.Menucontrolscanbeusedtosavevaluestobeappliedatsubsequentstart-upofthe
SCB-9050/9051.(Ifvaluesarenotsaved,thenthelastsavedsettingswillbeapplied.)
• A 22-18 gauge power wire is recommended for this camera.
• Voltage reinforcement will occur based on the length of the power wire. If the adapter
output wire is too long, camera performance may suffer.
Notes
IR camera Monitor
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samsung SCB-9051 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samsung SCB-9051 in the language / languages: English as an attachment in your email.

The manual is 6,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info