586982
37
Zoom out
Zoom in
Previous page
1/130
Next page
Network setup_ 37
1. Press Menu on the control panel.
2. Press the up/down arrow to highlight Information and
press OK.
3. Press the up/down arrow to highlight Con
figuration and press OK.
The machine prints the Config
uration Report.
Using this Conf
iguration Report, you can find your machine MAC address
and IP address.
For example:
MAC Address: 00:15:99:41:A2:78
IP Addres
s: 192.0.0.192
Setting IPv4 address
You must set up an IPv4 address for network printing and management. In
most cases a new IP address will be automatically assigned by a DHCP
(Dynamic Host Configuration Protocol) server located on the network.
If you use IPv6 address, refer to "IPv6 Configuration" on page 40
In a few situations the IP address must be set manually. This is called a
static IP and
is often required in corporate Intranets for security reasons.
DHCP IP assignment: Co
nnect your machine to the network, and wait a
few minutes for the DHCP server to assign an IP address to the
machine. Then, print the Configuration Report as explained above. If
the report shows that the IP address has changed, the assignment was
successful. You will see the new IP address in the report.
Static IP assignment: Use th
e SetIP program to change the IP address
from your computer. If your machine has a control panel, you can also
change the IP address using the machine's control panel.
In an office environment, we recommend that you contact a network admin-
istrator to set this address for you.
IPv4 setting using control panel
1. Connect your machine to the network with a network cable.
2. Turn on the machine.
3. Press Menu on
the control panel.
4. Press the u
p/down arrow to highlight Network and press OK.
5. Press the u
p/down arrow to highlight TCP/IP (IPv4) and press OK.
6. Press the u
p/down arrow to highlight Set IPv4 Address and press
OK.
7. Press the
u
p/down arrow to highlight Manual and press OK.
8. Enter the
IP address using numeric keypad and press OK.
9. In the same way, enter other parameters such as Subnet Mask and
-
Gateway and
press OK.
10. After entering
all parameters, press Stop/Clear to return to the ready
mode.
Now go to "Installing network connected machine’s driver" on page 38.
IPv4 setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your
machine using its MAC address to communicate with the machine. A
MAC address is the hardware serial number of the network interface and
can be found in the Configuration Report.
For using SetIP program, disable the co
mputer firewa
ll before continuing
by performing the following:
1. Op
en Control Panel.
2. Double click Secu
rity Center.
3. Click W
indows Firewall.
4. Disable the firewall.
Installing the program
1. Insert the Printer Software CD-ROM provided with your machine.
When the driver CD runs automatically, close that window.
2. Sta
rt a web browser such as Internet Explorer and open the X drive.
(X
represents your CD-ROM drive.)
3. Doub
le-click Applic
ation > SetIP.
4. Double-click Setu
p.exe to install this program.
5. Click OK. If necessary, se
lect a language from the drop-down list.
6. Follow the instructions in the window
and complete the installation.
Starting the program
1. Connect your machine and the computer using network cable.
2. Turn on the machine.
3. From the Win
dows Start menu, select All Programs > Samsung
Printers > SetIP > SetIP.
4. Click on the
icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5. Enter the machine’s new information into the configuration window
as follows:
MAC Address: Find the machine’s MAC address on the Config-
uration Report a
nd enter it without the colons. For example,
00:15:99:29:51:A8 becomes 0015992951A8.
A MAC address is a hardware serial number of the machine’s
network interface and can be found in the Configuration
Report.
IP Address: Enter
a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150,
enter 192.1
68.1.X. (X is number between 1 and 254 other than
the computer’s address.)
Subnet Mask: Enter a new Sub
net Mask for your machine.
Default Gateway: Ente
r a new Gateway for your machine.
6. Click Apply, and then click OK. The
machine will automatically print
the Configuration Report. Confirm that all of the settings are cor-
rect.
7. Click Exit to close the SetIP prog
ram.
8. If necessary, re
start the computer’s firewall.
IPv4 setting using SetIP Program (Mac)
For using SetIP program, disable the computer firewall before continuing
by performing the following:
The path and UIs may differ by Mac OS version. Refer to the Mac
OS manual to turn firewall off.
1. Open System Preferences.
2. Click Security.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samsung ML-551x Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samsung ML-551x Series in the language / languages: English as an attachment in your email.

The manual is 34,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Samsung ML-551x Series

Samsung ML-551x Series User Manual - German - 137 pages

Samsung ML-551x Series User Manual - Dutch - 132 pages

Samsung ML-551x Series User Manual - French - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info