629823
13
Zoom out
Zoom in
Previous page
1/20
Next page
9
Operating The ZM Series
Pre Announcement Chime
The ZM series mixer offers a useful Chime function to alert
listeners of an upcoming page. Simply press the front panel
Chime switch to play the chime.
In addition, the ZM series mixer can be set for one of four
selectable Chime tones by moving the internal shorting
jumpers as show in the figure below:
Priority Control
Channel 1 and 2 can be set for Priority operation. When
microphone channel 1 and 2’s Priority switch is set to the “ON
position, the other input channels will mute whenever signal
is present on the microphones connected to Channel 1 and 2.
Priority Mic Muting
In addition to the priority muting on microphones connected
to Channels 1 and 2, there are three levels of priority muting
which is always active. The priority muting is set in three
groups in the following order.
Chime and Tele page
Remote Mic
Channels 1 through 6
This means if there is a Tele-page or the Chime switch is
pressed, the Remote Mic and input Channels 1 through 6
are muted. If there is a signal on the Remote Mic, Channel
1 through 6 will be muted. The signals in the same priority
group will stay on together.
Connecting the Input Sources
Next, make the signal input connections, using the Euroblock
input connectors on the rear panel. If your mixer has balanced
outputs, we recommend the use of three-conductor cabling
and connectors (unbalanced two-conductor connections
can also be used, but you’ll get better signal quality and less
outside noise and hum if you use balanced lines).
On the front panel of the ZM Series, turn all the Channel input
controls fully counterclockwise (to their “MIN” setting). Then
connect the supplied heavy-gauge 3-pin “IEC” cable to the rear
panel IEC connector and to any grounded AC socket.
Press the front panel Power switch in order to turn on the ZM
Series. The Power LED will light and the Protection LED will go
on. After approximately five seconds, the Protection LED will
go off (you’ll hear a click when this occurs).
Apply an input signal to the ZM Series at or about +4dBu. Now
set the channel level to about half way up.
While the input signal is present, slowly raise the Master level
control until the desired sound level is achieved.
The SIGNAL and PEAK LED indicators will show you the
continuous power output of the ZM Series as signal is being
passed. For the best signal-to-noise ratio, the ZM Series
should normally be run with the Master level control at or
near maximum (fully clockwise, at the “MAX” position) and the
PEAK segments should light occasionally (but not frequently)
during peak levels. If the signal is too loud, use the Input level
controls attenuate the signals as necessary to achieve the
desired speaker level.
CD Player
Microphones
MIN MAX
ON OFF
PRIORITY
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson ZM75 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson ZM75 in the language / languages: English as an attachment in your email.

The manual is 2,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Samson ZM75

Samson ZM75 User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info