629823
12
Zoom out
Zoom in
Previous page
1/20
Next page
8
Operating The ZM Series
Setting up the ZM series
Setting up your ZM Series is a simple procedure, which takes
only a few minutes:
Remove all packing materials (save them in case of need
for future service) and decide where the amplifier is to be
physically placed—it can be used table-top or mounted in a
standard 19” rack (like the SRK equipment racks from Samson),
requiring only two rack spaces.
Install the rack ears by aligning them to the side of the unit,
flush to the front and install the supplied screws. Be careful
not to cross thread the screws. Then, remove the feet to allow
the unit to fit the 2 rack spaces.
When installed, make sure that both the front and rear panels
are unobstructed and that there is good ventilation around
the entire unit (we recommend the use of spacer panels,
especially if multiple amplifiers are used in a rack.
Connecting the Speakers to the ZM Amplifier
Make the speaker connections, using the Euroblock output
connectors on the rear panel. It is never a good idea to power
up any amplifier that is not connected to loudspeakers. When
operating using the 4-ohm output, any loudspeakers with
a minimum impedance load of 4 ohms (that is, 4 ohms or
greater) can be used.
For 70-volt operation, connect the positive input of the
speaker to the 70 Volt terminals and connect the negative
input the COM (ground) terminal.
The constant voltage output is set for either 70 or 100 Volts
depending on the country, however if can be changed by re-
configuring the internal transformer wires. Locate the T10, T11,
T12 and T13 terminals as per the diagram below.
Now follow the wiring chart below to select the required
operating voltage for constant voltage output.
-
+
8Ω 8Ω
4Ω
-
+
-
+
OUTPUT
COM
Constant Voltage 100V/70V/25V Lo-Z
OR
OUTPUT
C
OM
C
onsta
n
t
V
oltage 100V/70V/25V
L
o-Z
-
+
+
-
+
-
+
-
Matching
transformer
-
+
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson ZM75 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson ZM75 in the language / languages: English as an attachment in your email.

The manual is 2,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Samson ZM75

Samson ZM75 User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info