629822
8
Zoom out
Zoom in
Previous page
1/20
Next page
4
ZM Series Layout - Rear Panel
1- 25V, 70V and 100V (output connector) - Ten-
contact Euroblock connector for connecting the 25V,
70V and 100V constant voltage outputs.
2 - LO-Z (output connector)
- Two-contact Euroblock
connector for connecting the 4-Ohm speaker output.
3 - AMP IN and PRE-AMP OUT (connectors)
These
1/4-inch phone jacks are used to connect an external
effect processor.
4 - MOH VOLUME (control knob)
This control knob
allows you to adjust the level of the Music on Hold
sound source.
5 - MOH (selection switch)The slide switch is used
to chose the Music on Hold sound source from the
output of the internal mixer or an external sound
source (like a CD or MP3 player).
6 - CHIME VOLUME - (control knob)
The control knob
is used to adjust the level of the Chime tone.
7 - GAIN (control knobs)The trim knobs are used to
set the input sensitivity for each input channel.
8 - PRIORITY MIC (switch)
When set to on, this slide
switch configures mic channels 1 and/or 2 to mute
the other input channels when a signal is present on
the connected microphones.
9 - PHANTOM POWER (switch)
– Used this slide switch
to activate the phantom power on mic channels 1
and/or 2.
10 - MIC/LINE INPUTS (connectors) – Channels 1 and
2 employ combination connectors with XLR and
1/4-inch inputs, which can accept either mic or line
signals.
11 - MIC INPUTS (connectors) – Channels 3 and 4
are microphone level inputs on standard XLR
connectors.
12 - MIC/LINE INPUTS (connectors)
– Input channels 5
and 6 feature 1/4-inch and RCA connectors for mic
or line level input signals.
13 - REMOTE MIC input connector
– Connect the
paging microphone to this four-contact Euroblock
connector.
14 - REMOTE MIC GAIN (control knob)This trim
control is used to set the input sensitivity for the
remote microphone input.
15 - TELE PAGING (connector)
This three-contact
Euroblock connector is used to connect the ZM
series to a business telecom system so that pages
can be made from any handset.
16 - MOH OUTPUT (connector) - This three-contact
Euroblock connector is used to attach an external
sound source for the Music on Hold system.
17 - LINK IN and LINK OUT (connectors)
- Use these
connectors to expand your system by adding a
second ZM series mixer/amplifier.
18 - VOLTAGE SELECTION (switch)
- Used to select the
operation voltage for either 115 or 230 Volts. Be
sure to check the correct operating voltage for your
particular country.
19 - AC INLET
– Connect the supplied IEC power cable
here.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson ZM125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson ZM125 in the language / languages: English as an attachment in your email.

The manual is 2,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Samson ZM125

Samson ZM125 User Manual - French - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info