629990
9
Zoom out
Zoom in
Previous page
1/67
Next page
Operating The S•com plus
Whether you are an experienced audio engineer, just starting out, or you just want to experiment, follow the steps
below to get going. Further sections in this manual will cover basic dynamics and the associated parameters, sys-
tem set-ups and applications for using dynamics processing in recording and live sound applications.
SETTING UP THE S•com plus
• Connect one or both sets of inputs and outputs to the designated connectors on the rear panel.
• Set the controls to the following positions:
EXPANDER/GATE TRIGGER – OFF
GATE SWITCH – OUT
FAST RELEASE – OUT
COMPRESSOR THRESHOLD – +20dBu (fully clockwise)
ENHANCER - OUT
RATIO – 1:1
KEY SWITCH - OUT
ATTACK – 0.3 (fully counter-clockwise)
AUTO SWITCH- OUT
RELEASE - 5 (fully clockwise)
METER SWITCH – IN
OUTPUT LEVEL – O dBu
DE-ESSER – 0 (fully counter-clockwise)
DE-ESSER SWITCH – OUT
LIMITER – OFF (fully clockwise)
STEREO LINK SWITCH – OUT
CHANNEL 1 ENGAGE – OUT
EXPANDER/GATE COMPRESSOR / LIMITER
GAIN REDUCTION dB INPUT / OUTPUT LEVEL dB
30 24 2127 18 15 9 612 4 2 1 -30 -18 -12-24 -6 -3 +3 +60 +9 +12 +18
DE-ESSER LEVEL dB
-3 -60 -9 -12
LIMIT
CH 1
RELEASE AUTO I/O METER IN/OUT
dB
OFF +10
050
20
TRIGGER
GATE
10
-30
+20-40
+10
-10
THRESHOLD
dB
ENHANCER
62
1
RATIO
dB
4:1
KEY
ATTAC K
mSec
.3 300
20015
50
.05 5
3.15
1
RELEASE
Sec
-10
+20-20
+10
0
OUTPUT
dB
010
73
LEVEL
dB
5
0 OFF
16+5
LIMITER
dB
+12
IN/OUT 1
STEREO LINK
IN/OUT 2
STEREO
COMPRESSOR
LIMITER
DE-ESSER
In this configuration, the S•com plus is simply passing audio at unity gain with no dynamics processing. It is a
good idea to check your gain structure at this point. Use the Input/Output meter to match the level.
Send a signal to either or both of the S•com plus’ inputs and outputs.
Press the METER switch to see that the input and output levels are matched.
COMPRESSING A SIGNAL
S•com plus' Compressor section can be used for a variety of gain management tasks including printing signals to
a multi-track recorder, as a mix-down effect, mastering, and for increasing the loudness of a live PA system. To
begin compressing your signal, follow the steps below:
Follow the section above, “SETTING UP THE S•com plus” for normalizing the controls.
Press the CHANNEL IN switch (located in the middle of the unit) to the IN position.
Press in the AUTO switch (located in-between ATTACK and RELEASE).
Adjust the Ratio to 2:1.
ENGLISH
8
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson S.com plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson S.com plus in the language / languages: English as an attachment in your email.

The manual is 3,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info