Manual Samson S-Zone (page 12 of 108) (English, German, French, Italian, Spanish)

629661

Zoom out

Zoom in

1/108

Quick Start

We recommend that you take the time to read through

this manual, and then, use it as a reference guide. If you are

installing your first system you should read through the

section “Designing an Installation Plan” on page 6 before

you start connecting your S zone. If you’re a professional

installer you can skip over that section and if you want to

get started running some signals through your inputs and

outputs, you can follow the following quick start example.

Setting up your S zone is a simple procedure, which takes

only a few minutes. The following section describes the

set-up and operation of a simple installation using the S

zone with a CD player and paging microphone.

In this set up example, a paging microphone connected to

the S zone’s CHANNEL 1 input and a CD player connected to

CHANNEL 3. The S zone’s ZONE OUTPUT 1 is connected to a

pair of active (self powered) speakers. If you are using passive

speakers, the S zone’s ZONE OUTPUT should be connected to

the power amp input.

• Remove all packing materials (save them in case of

need for future service) and decide where the unit is

to be physically placed—it can be used freestanding

or mounted in a standard 19” rack (The S zone requires

only a single rack space).

• Make sure the power to all input sources (like CD, DVD,

MP3 & TAPE players) and amplifiers in your audio sys-

tem is off.

• Turn the volume control of your active speakers all the

way off. If you are using passive speakers with a sepa-

rate power amplifier, be sure to turn the power amp

volume controls all the way off.

Setting up the S zone

• On the front panel of the S zone, set all the VOLUME

control knobs to their bottom-most “OFF” setting.

• Set all ZONE OUTPUT LOW and HIGH Equalizer control

Knobs to their flat (“0”) center detented position.

• Now, make the S zone input connections, using the

Euroblock connectors on the rear panel.

• Next, make the S zone output connections, using the

Euroblock connectors on the rear panel.

• Plug in the supplied AC connector and connect it to

any standard AC socket.

• Press the front panel Power switch in order to turn on

the S zone.

• Power on your CD player, then power your active

speaker or power amp.

• On the Line 3 input channel, press the Zone 1 Switch.

• Apply an input signal from the CD player to the S zone

and slowly raise the front panel LINE 3 Volume control

knob to the “0” point.

• While the input signal is present, slowly raise the front

panel ZONE OUTPUT 1 control knob to the “0” point (if

sending signal from a CD Player, drive the mixer’s out-

put meters at approximately 0 VU).

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Samson S-Zone in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 11,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Samson S-Zone Manual

Product: