629739
7
Zoom out
Zoom in
Previous page
1/16
Next page
Connecting the Resound HD Speaker System
5
Choosing the Correct cables
The Resound HD series speaker connections are made via the rear panel 1/4-inch and/or Neutrik Speakon®
connectors. Standard, unshielded speaker wire, available at your local pro audio or music store, with either
1/4-inch phone or Speakon connectors and wire gauge of 12-14 is recommended.
If your amplifier uses binding posts you can use speaker cables with banana plugs, but be sure to pay atten-
tion to the plus and minus polarity when making the connections. It is important that your PA system is con-
nected in-phase otherwise you will not have the proper low-end response and stereo image.
In order to ensure that your PA system is-in phase, be careful to pay close attention to the positive and nega-
tive marking on the amplifier and wires. Make sure that the + terminal of the speaker, or banana connector,
is connected to the + terminal of the power amplifier and that the - terminal of the speaker, or banana con-
nector, is connected to the - terminal of the power amplifier.For a detailed wiring diagram, see page 9 of this
manual.
Heres a tip: Its fairly easy to identify a monitor that is out of phase just by listening, especially on a pop
recording. Listen for the parts of the music that you would expect to be in the center of the mix (like kick
drum and vocals). If you do not hear them directly in the center (for instance they sound like they are two
signals panned hard right and left), then you are more than likely listening to an out-of-phase monitor system.
(This test won’t work on early Beatles records where Ringos drum kit is panned all the to the right side. Try a
Madonna record.)
About Impedance
Before you hook up your speaker cabinet, be sure that you understand a little about impedance. Impedance is
the electronic load that the speaker puts on the power amplifier and is measured in Ohms.
Here is the tricky, yet simple rule of impedance: When two speakers, of equal impedance are wired in "Parallel",
like when you use the Extension Output, the total impedance is cut in half. When two speakers are wired in
“Series”, (usually for internal cabinet wiring only), the total impedance is the sum of the speakers individual
impedance.
Each of the Resound HD models, EXCEPT the RS215HD is 8 Ohms. So, when two Resound HD models (EXCEPT
the RS215HD) are connected together in parallel, the total impedance is 4 Ohms. The RS215HD impedance
is 4 Ohms. So, when two RS215HD’s are connected together in parallel, the total impedance is 2 Ohms. The
impedance of your speaker also has an effect on your amplifier. In general, the lower the impedance, the more
power your amplifier will put out.
IMPORTANT NOTE: There is minimum safe impedance for running power amplifiers so be sure to check the
manufacturers recommended impedance for your amplifier to avoid any damage to your amplifier or voiding
your warranty.
Using the EXTENSION Output
The Resound HD models provide a convenient Extension Output for connecting additional speaker cabinets
in parallel. Be sure to read the section above on impedance to insure a proper hook up with your amplifier. To
connect two Resound HDs using the Extension output, connect your amplifier output to the Input of the first
Resound HD and then, connect the Extension Output to the Input of the second Resound HD.
Powering the Resound HD
Each of the Resound HD loudspeakers have a specific power rating, which is printed on the input jack-plate,
and also, in the Specification section on page 10 of this manual. Be sure to check that your power amp has the
correct power output for your Resound HD. Be careful to consider the total impedance if you are connecting
more the one Resound HD to one side of a stereo power amplifier. Using a power amplifier with too low of a
power rating can be dangerous since the output signal is often clipped in an effort to get the desired level.
Over powering the Resound HD can result in catastrophic failure and therefore using any amplifier with a
power rating over the recommend power rating may void your warranty.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson RS10mHD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson RS10mHD in the language / languages: English as an attachment in your email.

The manual is 1,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info