629655
13
Zoom out
Zoom in
Previous page
1/112
Next page
13
MXP144/MXP144FX
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO
Stereo Input Channel Section
The following section details four stereo input channels.
14. MIC Inputs (CH5/6 & CH7/8) - Use these balanced XLR
inputs to connect low Impedance microphones and low
level signals from direct boxes. The MIC inputs feature
+48V phantom power, allowing you to use condenser
microphones.
XLR Connector pin-out - Pin 1: Ground, Pin 2: Hot (+),
Pin 3: Cold (-)
15. Stereo ¼” Input Jacks - Use the ¼” jacks for connecting
stereo line level sources. For stereo inputs use the LINE L to connect
the left channel and the LINE R to connect the right channel. Use the
LEFT input when connecting a mono input signal to the Stereo Input
channels. You can connect outputs from high impedance microphones,
synthesizers and drum machines to these inputs. The LINE inputs have a
nominal operating level of -40dBV through - 10dBV.
TRS phone jacks Connector pin-out - Sleeve: Ground, Tip: Hot (+), Ring:
Cold (-)
16. Stereo RCA Input Jacks (CH9/10 & 11/12) - The stereo
channel’s RCA connectors accept signals from stereo
line devices. The RCA line level inputs have a nominal
operating level of -40dBV through - 10dBV.
17. Equalizer (HIGH, MID, and LOW) - This three-band
equalizer allows you to contour a channel’s high, mid,
and low frequency bands. When the control is set to the
12 o’clock (detent) position, there is no effect on the
signal. Turning the controls fully clockwise will raise the
level of the frequency band +15 dB, while turning the
controls fully counterclockwise will lower the level of
the frequency band -15 dB.
18. MON Auxiliary Control - Controls the amount of that
channel’s signal that is sent to the MON Output. The
signal feeding MON is sent before, or pre, the channel
fader, so the channel fader has no effect on the MON
level. The MON is usually used to create a separate mix
for a floor monitor system.
19. FX Auxiliary Control - The channel’s FX knob controls the amount of signal
that is sent to the effects bus. The signal of the FX bus in the MXP144FX
is routed to the Digital Effects section for on-board signal processing. The
FX signal can also be sent to an external effect device connected to the
FX SEND jack located on the front panel jack field.
Top Panel Controls
14
15
16
17
18
19
20
22
23
21
16
17
18
19
20
22
23
21
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson MXP144 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson MXP144 in the language / languages: English as an attachment in your email.

The manual is 9,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info