629655
11
Zoom out
Zoom in
Previous page
1/112
Next page
11
MXP144/MXP144FX
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO
Mono Input Channel Section
The following section details four mono input channels.
1. MIC Inputs - Use these balanced XLR inputs to connect
low Impedance microphones and low level signals from
direct boxes. The MIC inputs feature +48V phantom
power, allowing you to use condenser microphones.
XLR Connector pin-out - Pin 1: Ground, Pin 2: Hot (+),
Pin 3: Cold (-)
2. Line Level Input - Use these balanced TRS ¼” inputs to
connect synthesizers, drum machines, effects processors
or any line-level signal. You can connect balanced and
unbalanced devices to these inputs.
TRS phone jacks Connector pin-out - Sleeve: Ground,
Tip: Hot (+), Ring: Cold (-)
3. INSERT (Send and Return) Jack - The ¼” TRS (Tip, Ring,
Sleeve) INSERT jack is for connecting outboard effects processors directly
on the channel input. The signal is sent on the tip (the Send) and returns
on the ring (the Return) of the connector.
4. GAIN Control - Variable GAIN control with a range of +5 to +45dB on the
MIC input and -20 to +20dB on the LINE input.
5. HPF Switch - The high pass filter rolls off the low frequencies from the
XLR MIC inputs from 80Hz and below at the rate of 12dB per octave. The
high pass filter allows you to remove the lower frequencies that you don’t
want the microphone to pick up. In live sound applications, the high pass
filter is useful for removing stage rumble.
6. COMP Control - The COMP knob adjusts the level of
compression applied to the channel. As the COMP knob
is turned clockwise, the compression ratio is raised and
the output gain is adjusted accordingly. The dynamic
range of the channel is narrowed, where softer signals
will be magnified and loud signals will be subdued to sit
better in the mix. Too much compression can create a
pumping effect, eliminate all dynamic range, and lead
to feedback.
7. Equalizer (HIGH, MID, and LOW) - This three-band
equalizer allows you to contour a channel’s high, mid,
and low frequency bands. When the control is set to the 12 o’clock
(detent) position, there is no effect on the signal. Turning the controls
fully clockwise will raise the level of the frequency band +15 dB, while
turning the controls fully counterclockwise will lower the level of the
frequency band -15 dB.
Top Panel Controls
1
2
3
4
5
6
11
7
8
9
10
12
13
1
2
3
4
5
6
11
7
8
9
10
12
13
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson MXP144 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson MXP144 in the language / languages: English as an attachment in your email.

The manual is 9,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info