Manual Samson Expedition Pro XP 200 (page 12 of 60) (English, German, French, Spanish)

629790

Zoom out

Zoom in

1/60

Expedition Pro XP300

6: Line inputs - Use these 1/4" jacks to connect line-level sources to the XP300. Channels 1 and 2 are

mono 1/4" connectors; channel 3/4 uses a stereo (TRS) 1/4" connector, with tip carrying left signal and

ring carrying right signal. Stereo devices should always be connected to the stereo channel (channels

3/4). If a wireless receiver is connected to the XP300 via its internal connectors (see page 14 in

this manual), its output arrives at channel 2, which can also carry another line-level source connected

to its line input, as well as signal from a microphone connected to its mic input. If an optional TD30

cassette player is installed, its output arrives at channels 3/4, which can also carry another two line-level

sources (one connected to its line input and a second connected to the CD inputs [see #15 on the fol

lowing page]), as well as signal from a microphone connected to its mic input.

7: Mic inputs - Use these XLR jacks to connect microphones to the XP300’s built-in mic preamps.

Each channel can carry both one or more line level sources (see #6 above) as well as a mic source.

8: DSP Effects control - Use this to select one of six reverb presets (Small Hall, Medium Hall, Large Hall,

Church, Stadium, or Plate). If you don’t want to hear any reverb, set this switch to the “Off” position.

9: Mono/Stereo switch - When using one XP300, set this switch to “Mono” so that the XP300 power

amp receives signal from both the left and right output sections. When using multiple Expedition Pro

speaker enclosures, set this switch to “Stereo”; the XP300 will then reproduce only signal from the left

output section only (that is, signals panned left at the mixer); the Right output can then be used to send

signal from the right output section (that is, signal panned right at the mixer) to a second enclosure.

See the interconnection diagrams on pages 10 - 11 for more information.

10: Outputs - The dual XLR connectors carry line-level output signal from the XP300. They are used to

send signal to a second XP300 (or XP200) being daisy-chained (see the interconnection diagram on the

following page) or to an optional EX500 subwoofer. Note that the signal being output from these con

nectors is dependent upon the setting of the Mono/Stereo switch (see #9 above). When set to “Stereo,”

the Left XLR connector carries left signal only and the Right XLR connector carries right signal only;

when set to “Mono,” both the Left and Right connectors carry the same monophonic signal, summed

from both the left and right output sections. See the interconnection diagrams on pages 10 - 11 for

more information.

11: Main Volume control - This knob determines the final output signal level—you can think of this as

being the “master fader.” Signals from all four channels are routed here just before being routed to the

XP300’s built-in power amplifiers and Left and Right output jacks (see #10 above).

12: Battery VU meter - If an optional RB 2030 rechargable battery pack is installed, this meter shows

how much battery power remains as it is being charged (Power switch off) or depleted (Power switch

on). See #20 on the following page.

13: Output VU meter - This three-segment bar meter shows the continuous output level of the XP300.

For optimum signal-to-noise ratio, try to adjust all channel and main Volume controls so that program

material is usually at or around 0 VU, with occasional but not steady excursions to the red “+3 dB” seg

ment.

14: Limiter LED - Lights whenever the built-in limiter is active. If you see this lighting frequently, it

means you’re overloading the XP300, so turn down one or more of the Channel volume controls (see #4

on the preceding page) or the main Volume control (see #11 above).

15: CD inputs - Connect the outputs of a CD or tape player to this set of dual phono jacks. Signal

arriving here returns to stereo channel 3/4. If an optional TD30 cassette player is installed, note that its

output also arrives at channels 3/4, in addition to line-level signal arriving at its 1/4" TRS line input (see

#6 on the preceding page) and signal from a microphone connected to its mic input (see #7 on the pre

ceding page).

16: AC input - Connect the supplied heavy-gauge 3-pin “IEC” power cable here.

ENGLISH

I' am trying to find a service manual for the xp200 without success. I have two units that were not plugged for two years and will no take a charge. How do I replace the batter? It looks like the case comes apart by removing the screws around the outer perimeter ,one at the top and two underneath at the bottom. Are there any special precautions when separating the front from the main body? Submitted on 13-9-2022 at 01:36
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Samson Expedition Pro XP 200 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 10,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Samson Expedition Pro XP 200 Manual

Product: