647728
7
Zoom out
Zoom in
Previous page
1/16
Next page
6
7
3. CONNECTING THE CUFF TO THE MONITOR
The cu is attached to the monitor when it is packaged. Should the cu become
unattached, align the two plugs and four brackets of the cu with the plug sockets
and bracket sockets of the monitor and press the cu to the monitor until the
plugs and brackets are securely attached.
4. APPLYING THE CUFF
a. Place the cu around a bare wrist 1-2cm above the wrist joint on the palm side of the wrist.
b. While seated, place the arm with the cued wrist in front of your body on a desk or table with the palm
up. If the cu is correctly placed, you can read the LCD display.
c. The cu must be neither too tight nor too loose.
Note:
1. Please refer to the cu circumference range in “SPECIFICATIONS” to make sure that the appropriate cu
is used.
2. Measuring on same wrist each time.
3. Do not move your arm, body, or the monitor during measurement.
4. Stay quiet, calm for 5 minutes before blood pressure measurement.
5. Please keep the cu clean. Clean the cu by wet soft cloth and mild detergent if the cu becomes dirty. Do not
remove the cu from the monitor. Clean the cu after the usage of every 200 times is recommended.
5. BODY POSTURE DURING MEASUREMENT
Sitting Comfortably Measurement
a. Be seated with your feet flat on the floor, and don’t cross your legs.
b. Place palm upside in front of you on a flat surface such as a desk or table.
c. The middle of the cu should be at the level of the right atrium of the heart.
6. TAKING YOUR BLOOD PRESSURE READING
a. After applying the cu and your body is in a comfortable position, press the “START” button. A beep is heard and all
display characters are shown for self-test. See picture 6. Please contact the service center if segment is missing.
Picture 6 Picture 6-1 Picture 6-2 Picture 6-3
b. Then the monitor starts to seek zero pressure. See picture 6-1.
c. The monitor inflates the cu until sucient pressure has built up for a measurement. Then the monitor slowly
releases air from the cu and carries out the measurement. Finally the blood pressure and pulse rate will be
calculated and displayed on the LCD screen separately. Irregular heartbeat symbol (if any) will blink. See picture
6-2&6-3. The result will be automatically stored in the memory bank.
d. After measurement, the monitor will turn o automatically after 1 minute of no operation. Alternatively, you can press
the “START” button to turn o the monitor manually.
e. During measurement, you can press the “START” button to turn o the monitor manually.
Note: Please consult a health care professional for interpretation of pressure measurements.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Salter BPW-9100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Salter BPW-9100 in the language / languages: English as an attachment in your email.

The manual is 1,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info