647728
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
7
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
17. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
18. This blood pressure monitor is verified by auscultatory method. It is recommended that you check annex B of ANSI/
AAMI SP-10:2002+A1:2003+A2:2006 for details of verification method if you need.
SETUP AND OPERATING PROCEDURES
Fully Automatic Electronic Blood Pressure Monitor is for use by medical professionals or at home and is a non-invasive
blood pressure measurement system intended to measure the diastolic and systolic blood pressures and pulse rate of an
adult individual by using a non-invasive technique in which an inflatable cu is wrapped around the wrist.
1. BATTERY LOADING
a. Open battery cover at the back of the monitor.
b. Load two “AAA” size batteries. Please pay attention to polarity.
c. Close the battery cover.
When LCD shows battery symbol , replace all batteries with new ones.
Rechargeable batteries are not suitable for this monitor.
Remove the batteries if the monitor will not be used for a month or more to avoid relevant damage of battery leakage.
Avoid the battery fluid to get in your eyes. If it should get in your eyes, immediately rinse with plenty of clean water
and contact a physician.
The monitor, the batteries and the cu, must be disposed of according to local regulations at the end of their usage.
2. CLOCK AND DATE ADJUSTMENT
a. Once you install the battery or turn o the monitor, it will enter Clock Mode, and LCD will display time and date by
turns. See picture 2&2-1.
Picture 2 Picture 2-1 Picture 2-2
b. While the monitor is in Clock Mode, pressing both the “START” and “MEM” button simultaneously, a beep is heard and
the month will blink at first. See picture 2-2. Press the button “START” repeatedly, the day, hour and minute will blink
in turn. While the number is blinking, press the button “MEM” to increase the number. Keep on pressing the button
“MEM”, the number will increase fast.
c. You can turn o the monitor by pressing “START” button when the minute is blinking, then the time and date is
confirmed.
d. The monitor will turn o automatically after 1 minute of no operation, with the time and date unchanged.
e. Once you change the batteries, you should readjust the time and date.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Salter BPW-9100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Salter BPW-9100 in the language / languages: English as an attachment in your email.

The manual is 1,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info