767114
2
Zoom out
Zoom in
Previous page
1/28
Next page
4358-6489
Forward Facing: 22-65 lbs. ( 10.1-29 kg)
34-49 in. (85.1-125 cm) and at least 1 year old
Belt Positioning Booster: 40-100 lbs. (18.1-45.4 kg)
43-52” (110.1-132.1 cm)
and at least 4 years old
Summit 65
55
CUT ON DOTTED LINE
Replacement Parts List
NOTE: If requested color is not available, similar color will be
substituted. Prices are subject to change.
Part ..................... Cost ................Qty...................Total Cost
Buckle Strap..........$7.99 ...............___ ................... $_______
Harness Strap .......$2.99 ...............___ ................... $_______
Seat Pad ................$39.99 .............___ ...................$_______
(Includes headrest and harness covers)
Chest Clip ..............$1.50 ...............___ ................... $_______
Top Anchorage
(Tether) Kit ............$9.99 ...............___ ...................$_______
LATCH Kit ..............$24.99 .............___ ...................$_______
Instructions ........... $0.00 ...............___ ................... $_______
Locking Clip ..........$2.50 ...............___ ...................$_______
Merchandise Total...................... ......................$_______
Shipping and handling:.............. ......................$_______
Sales Tax ..........................................................$_______
(Arizona, California, Georgia, Indiana, Missouri, South Carolina, and Texas
residents add applicable sales tax.)
Grand Total .................................... ..................$_______
No shipping and handling on instructions for quantities under 6. Add $.50 for each
instruction over 6, then add applicable shipping and handling.
Fill Out For Credit Card
q Visa q Mastercard
Card Exp. Date:______________________________
Cardholder’s Name:___________________________
Card Number:________________________________
Signature__________________________________
Up to $25.00 .............$5.95
$25.01 to $50.00 ......$6.95
$50.01 to $75.00 ......$8.95
$75.01 to $100.00 ....$9.95
$100.01 to $150.00 ..$10.95
$150.01 to $200.00 ..$11.95
$200.01 and up .......$13.95
Outside Continental USA $10.00
©2013 Cosco Management Inc. All Rights Reserved.
A. Before You Begin ................................Pages 3-7
A-1 Thank You...
A-2 Registration and Safety Notices
A-3 Understanding Your Child Restraint
B. Safety Information .............................Pages 8-9
B-1 Vehicle Seating Position
B-2 Installation in Vehicle
B-3 Child Restraint Use
C. Basic Use ............................................Pages 10-29
C-1 Choosing Position for Your Child
C-2 Preparing Child Restraint to Fit Your Child
C-3 Securing Child in Child Restraint
C-4 Removing Child from Child Restraint
C-5 Removing Harness System
C-6 Installing Harness System
C-7 Removing Seat Pad for Cleaning
C-8 Accessories
E. Installing Forward-Facing .......... Pages 36-43
D. General Vehicle Installation ....Pages 30-35
D-1 Understanding Your Vehicle
D-2 Vehicle Seating Position
D-3 Choosing LATCH or Vehicle Belts
D-4 Knowing Your Vehicle Belts
D-5 Aircraft Information
12
F-1 Preparing Belt-Positioning Booster
F-2 Installing Using the Lap and Shoulder Belts
F. Belt-Positioning Booster Use ..... Pages 44-48
E-1 Preparing to Install Forward-Facing
E-2 Adjusting Top Anchorage Strap (Tether)
E-3 Preparing to Install LATCH Forward-Facing
E-4 Installing Forward Facing With LATCH
E-5 Installing Forward Facing with Vehicle Belts
General Information ..........................Pages 49-55
Using a Locking Clip
Warranty
Replacement Parts Order Form
A. Before You Begin
Thank you for choosing this car seat, referred to throughout
this manual as a child restraint. The DJG family is committed
to creating a child restraint with the most comfort and
convenience available today.
Remember, parents are a child’s first teachers and examples.
If you always buckle your seat belt, your child will think it is
the natural thing to do. Make it a firm rule that the vehicle
does not go until everyone is buckled up. Make no exceptions.
No one can predict if use of a child restraint will prevent injury
or death in a particular crash. However, combined with careful
driving, proper use of a child restraint can lower a child’s risk
of injury or death in most crashes.
Your child’s safety is worth the time it will take to read and
follow these instructions. After reading, if you still have
questions or have any problems with this child restraint,
please contact our Consumer Relations Department at:
Dorel Juvenile Group, Inc.
Website: www.djgusa.com
Fax: 1-800-207-8182
Mailing Address: Dorel Juvenile Group, Inc.
P.O. Box 2609
Columbus, IN 47202-2609
Telephone: 1-800-544-1108
8 A.M. to 6 P.M. EST M-TH
8 A.M. to 4:30 P.M. EST FRI
On the back of the shell there is an expiration date for use of
this child restraint. Do not use this child restraint after the
expiration date.
A-1 Thank You...
Para recibir las instrucciones en español, llame al
1-800-544-1108 o solicitarse por escrito al dirección por arriba.
Please complete the postage-paid registration card that
came with your child restraint, and send it to us. Child
restraints could be recalled for safety reasons. You must
register this restraint to be reached in a recall. Send
your name, address, email address if available, and the
restraint’s model number and manufacturing date to:
Dorel Juvenile Group, Inc.
PO Box 2609, Columbus, IN 47202-2609
Attn: Consumer Relations
or call 1-800-544-1108 or register online at www.djgusa.
com/registration/carseat/us.
For recall information, call the U.S. Government’s Vehicle
Safety Hotline at 1–888–327–4236 (TTY: 1–800–424–
9153), or go to http://www.NHTSA.gov
If you don’t have the card or if your
address changes, you will find the
model number and manufactured date
on the label located on side of plastic
shell.
A-2 Registration and Safety Notices
Model
Number
Manufacture
Date
34
Example of model number and manufacture date.
A. Before You Begin
5
A-3 Understanding Your Child Restraint
Front View Harness System Detail
A. Adjustable Headrest
B. Shoulder Belt
Positioning Guide
C. Armrest
D. Vehicle Belt Path for
Booster Seat Use
E. Harness Release Lever
(under flap)
F. Harness Tightening
Strap
G. Cup Holder
H.
I.
J.
K.
M.
O.
L.
N.
C.
D.
B.
A.
E.
F. G.
H. Upper Harness Slots
I. Harness Strap
J. Harness Covers
K. Chest Clip
L. Buckle Tongues
M. Buckle
N. Lower Harness
Guides
O. Buckle Slots
6
B. Safety Information
8
B-1 Vehicle Seating Position
According to accident statistics, children
are safer when properly restrained in the
rear seating positions than in the front
seating positions.
Check the vehicle’s owner manual for
more information about airbag/child
restraint use.
For vehicles without a back seat, refer
to your vehicle’s owner manual.
Failure to follow these warnings can result
in the serious injury or death of your child.
To help you recognize instructions which
are most critical to your child’s safety, we
use this symbol:
B-2 Installation in Vehicle
Check the vehicle belt or LATCH belt
before each use. Use only if the belt is
tightened properly and securely.
This child restraint should be securely
belted in the vehicle even when not in use.
In a crash or sudden stop, an unsecured
child restraint could injure occupants.
Do not use a child restraint that has
been in a crash. You must get a new child
restraint.
7
Back View
B.
C.
H.
E.
F.
G.
D.
A.
I.
J.
A. LATCH Attachment for
Storage
B. Shoulder Belt
Positioning Guide
C. Headrest Adjuster
D. Forward-Facing Belt
Path
E. LATCH Belt
F. Instruction Storage
(in kickstand)
G. Kickstand
H. Splitter Plate
I. Top Anchorage Strap
(Tether) & Hook
J. Tether Storage
C. Basic UseC. Basic Use
9
B-3 Child Restraint Use
Do not use this child restraint unless the
child is 22-100 lbs (10.1- 45.4 kg) and
34-52 in. 85.1-132.1 cm).
Never take your child out of the child
restraint while the vehicle is t.
Never leave child unattended.
Placing your child in a hot child restraint
may result in burns.
Do not use a child restraint with
damaged or missing parts.
Do not use cut, frayed or damaged
harnesses.
Do not lubricate buckles and fasteners.
Do not substitute parts or try to modify
the child restraint in any way.
Do not use any child restraint accessory
except those approved by Dorel Juvenile
Group.
Never allow any child to play with this
child restraint; it is not a toy.
Do not remove or cover up any of the
warning labels or other labels on the child
restraint.
Read all instructions for additional
warnings.
C-1 Choosing Position for Your Child
10
Your child’s height, weight and age determine how your child
restraint should be placed in the vehicle.
40-100 lbs (18.1-45.4 kg)
and 43-52 in.
(110.1-1
32.1
cm) and at
least 4 Years Old
Belt-positioning
booster using vehicle
lap/shoulder belt
combination
Child and child restraint are
placed in the back seat,
facing the front of the
vehicle.
5-point harness is removed.
22-65 lbs (10.1-29 kg)
and 34-49 in.
(85.1-125 cm) and
at least 1 Year Old
Forward-Facing using
5-point harness
Child and child restraint are
placed in the back seat,
facing the front of the vehicle.
C. Basic Use
11
Remove LATCH Belt
from Packaging
Fold Out Kickstand
Rotate kickstand down
and out, then push up to
lock.
Kickstand MUST be
folded out in order to
use this seat.
Store LATCH
Store Top Anchorage
Strap (Tether)
2.
1.
3.
4.
continued on next page.
C-2 Preparing Child Restraint to Fit
Your Child
You MUST make these adjustments with your child
before you install the child restraint in the vehicle.
Release Chest Clip
Press on chest clip release
button and pull apart.
6.
Unbuckle Harness
Press red button.
Pull buckle tongues out.
Place harness straps out
of the way.
7.
Place Child in Child
Restraint
Place the child’s bottom
and back flat against the
restraint.
This will allow the harness
straps to be properly
tightened.
8.
Loosen Harness
Push down on the harness
release lever (under flap on
the front of restraint) while
pulling out on the harness.
5.
12
C. Basic Use
Check Buckle
Position
Determine which of the
available buckle positions
will provide a snug fit for
your child.
9.
To Change Buckle
Position
Turn the child restraint
over and locate buckle’s
metal retainer on bottom
of shell.
10.
Rotate metal retainer, then
insert retainer up through
the shell and pad.
a.
From the top, pull buckle
free from shell and pad.
b.
13 14
Insert the buckle’s metal
retainer through the
desired slot.
Make sure that the buckle
is facing out.
c.
Pull buckle’s metal
retainer completely
through pad and shell.
d.
Pull up on buckle to make
sure it is secured.
The buckle must not pull
out.
e.
Failure to place buckle’s metal retainer
completely through pad and shell can result
in serious injury or death.
continued on next page.
C. Basic Use
15
Check Harness/
Headrest Height
With child in the seat, check
the location of the harness
slot.
Follow the guidelines below
to determine the correct
harness height.
Forward-Facing Position
Upper harness slots must be even
with or just above the shoulders.
If the harness is below the child’s
shoulders in the highest harness
position and the child weighs at
least 40 lbs. (18.1 kg) and is at least 4 years old, convert
the seat to a belt-positioning booster.
To Change Harness
Location
From the back of the seat,
remove harness from
splitter plate.
Pull Harness Out of
Shell From the Front
12.
a.
Rethread Harness
Into Correct Harness
Location
Make sure harness does
not twist.
Squeeze the headrest
adjuster on the back of the
seat.
Slide the headrest to the
correct position. Make
sure it locks into place.
d.
16
Adjust Headrest
The choosen harness slot
height and the headrest
position MUST match
locations.
b.
c.
4
4
3
3
2
2
1
1
Thread Harness OVER
Metal Bar
Pull harness through the
back.
Harness MUST go OVER
the metal bar and lay
BETWEEN the metal bar
and plastic handle of the
headrest adjuster.
e.
11.
continued on next page.
C. Basic Use
Harness straps
MUST be threaded
over the metal bar
and lay between the
metal bar and the
plastic handle of the
headrest adjuster.
Do not use this child restraint
forward facing if the midpoint
of your child’s head is above
the top of the child restraint’s
headrest.
Make sure the harness height is correct
for your child’s size.
Failure to follow these steps can result
in serious injury or death.
17
Tighten Harness
Pull on harness
tightening strap to tighten
harness snugly.
NOTE: A snug strap should
not allow any slack. It lies
in a relatively straight line
without sagging. It does not press on the child’s flesh or
push the child’s body into an unnatural position.
18
C-3 Securing Child in Child Restraint
Position Harness
Straps Over the
Child’s Shoulders
1.
Buckle Harness
Push each buckle tongue
into buckle until you hear a
“click.”
Pull up on harness straps to
make sure buckle is locked.
2.
Close Chest Clip
Insert right half of chest
clip into left half and snap
together.
3.
4.
Attach Harness Straps
to Splitter Plate
From the back of the child
restraint, fit the harness
strap loops onto the splitter
plate.
Make sure sewn ends
of the harness strap loops face towards you. DO NOT
twist harness straps or harness tightening strap and
make sure the harness straps are COMPLETELY ON the
splitter plate.
f.
continued on next page.
C. Basic Use
19
Position Chest Clip
The chest clip must be
placed at mid-chest (even
with armpits) and away
from the child’s neck.
6.
Failure to fasten and tighten the harness
system correctly and snugly can result in
serious injury or death.
Check Harness
Tightness
Try to pinch the harness at
the shoulders.
If you can pinch the
harness strap, tighten
more.
If your fingers slip off, the
harness is tight enough.
5.
20
C-4 Removing Child From Child Restraint
Loosen Harness
Press on harness release
lever while pulling on
harness straps above the
buckle to loosen.
1.
Release Chest Clip
Press on release button and
pull apart.
2.
Unbuckle
Press red button on buckle
to release the buckle
tongues. Move harness
away from child and
remove child.
3.
C. Basic Use
21 22
Harness system MUST be removed to use this
child restraint as a Belt-Positioning Booster.
Remove Harness
Straps from Splitter
Plate
Fully loosen harness
straps. Locate splitter plate
on the back of the seat
and unfasten the harness
straps.
1.
Secure Splitter Plate
Pull out on harness
tightening strap so that
the splitter plate is flush
against the bottom of the
shell.
2.
Remove Harness
Straps
(1) Pull harness through
the slots from the front.
(2) Unthread harness from
the chest clip.
(3) Do not unbuckle the
buckle. Unthread harness
from the buckle tongues.
(4) Pull harness out of shell.
3.
C-5 Removing Harness System
1
2
3
4
Remove Buckle
Turn the child restraint
over and locate buckle’s
metal retainer on bottom
of shell.
Rotate metal retainer,
then insert retainer up
through the shell and
pad.
From the top, pull buckle
free from shell and pad.
4.
5.
Store the harness straps, chest clip, buckle
tongues and buckle for future use.
Thread Harness Strap
(1) With sewn end of
the harness strap loop
facing the buckle, thread
the harness strap down
through lower harness
guide on left side of shell.
(2) Pull across bottom of
shell and up through lower
harness guide on right
side of shell.
Harness tightening strap MUST lay between shell
and harness strap as shown.
Take both ends of the
harness strap and make
them even in length.
The sewn ends of the
harness strap loops MUST
face each other as shown.
C. Basic Use
23 24
C-6 Installing Harness System
Install Buckle
Insert the buckle’s metal
retainer through the
desired slot.
Make sure that the buckle
is facing out.
Pull buckle’s metal
retainer completely
through pad and shell.
Check Buckle
Pull up on buckle to make
sure it is secured.
The buckle must not pull
out.
Failure to place buckle’s metal retainer
completely through pad and shell can result
in serious injury or death.
1.
a.
b.
continued on next page.
(3) Thread left harness strap
through the back of the left
buckle tongue. Repeat for right
harness strap.
(4) Thread the chest clip from
front to back as shown.
(5) Push harness ends through
upper harness slots at the
same height.
DO NOT twist harness straps.
b.
5
4
4
3
2.
1
2
a.
C. Basic Use
25 26
Thread Harness OVER
Metal Bar
Pull harness through the
back.
Harness MUST go OVER the
metal bar and lay BETWEEN
the metal bar and plastic
handle of the headrest
adjuster.
c.
Attach Harness Straps to
Splitter Plate
From the bottom of the child
restraint, fit the harness strap
loops onto the splitter plate.
The sewn end of the
harness strap loops MUST
face towards you. DO NOT
twist harness straps or
harness tightening strap and make sure the harness
straps are COMPLETELY ON the splitter plate.
Failure to place the harness
tightening strap between
shell and the harness
straps as shown can result
in serious injury or death.
Harness straps MUST be
threaded over the metal
bar and lay between the metal bar and the
plastic handle of the headrest adjuster.
Harness system must be reattached
correctly.
Failure to follow these warnings can result
in serious injury or death.
3.
C-7 Removing Seat Pad for Cleaning
You must remove the harness system to remove the
pad. See section C-5.
Remove the Elastic
Straps
From the back, release the
elastic straps at the top and
sides of the restraint.
2.
Remove Headrest Pad
Place headrest in the
highest position. Starting
from the top, gently pull
pad off of headrest.
Release the elastic straps
at the bottom of the
restraint.
a.
1.
continued on next page.
C. Basic Use
27 28
Remove Harness Guides
From the bottom of the
restraint, locate lower harness
guides.
Push harness guide lip
toward outside of plastic shell
with one hand while pulling
harness guide from the front
with the other.
3.
Lower Harness Guides
Remove Pad From Shell
From the top, pull pad off
shell and over headrest.
Remove pad from shell.
4. Undo Fastening Strip
Behind Headrest
Lower headrest to lowest
position and undo the
fastening strip behind the
headrest. Pull seat pad
down from behind the
headrest.
5.
Replace the Seat Pad
Replace seat pad by reversing order:
Lower headrest.
Starting from bottom of child restraint, slip pad on shell.
Pull harness adjustment strap through pad.
Make sure pad is behind headrest. Attach fastening strips.
Attach all of the elastic straps.
Place headrest in highest position. Gently pull headrest pad
on headrest.
Install lower harness guides.
Install harness system (see section C-6).
Do not use child restraint without the seat
pad. Failure to do this can result in serious
injury or death.
Cleaning Seat Pad
Hand wash pad with warm sudsy water, rinse clean and air
dry. Spot clean the harness straps. Do not use bleach or
other harsh cleaners. Do not dry clean.
D. General Vehicle Installation
29 30 continued on next page.
Your vehicle’s features may be considerably different than
those pictured here. Consult your vehicle’s owner manual to
help identify your vehicle’s specific features and locations.
D-1 Understanding Your Vehicle
Anchor Brackets
For Top Anchorage
Strap (Tether)
(Forward-Facing Only)
LATCH Anchors
Located in the seat
bight.
Airbags
Consult your vehicle’s
owner manual for all
airbag locations.
Seat Bight
Vehicle Seat Belts
Consult your vehicle’s
owner manual for
vehicle belt use.
Safety Tip:
To avoid your child being seriously burned,
take the following precautions:
1. Park in the shade or where sun does not
directly hit the child restraint.
2. Cover the child restraint with a sheet or blanket
when not in use.
3. Check for hot seat and buckles before placing
child in child restraint.
To help protect your vehicle seat’s upholstery from damage,
use a single layered towel underneath and behind child
restraint.
C-8 Accessories
Cup Holder
(on select models)
Pull pad off corner at child’s
left side. Hook bottom of
cup holder to edge of shell.
Rotate cup holder up until it
snaps into the hole on the
shell.
Replace pad.
Harness Covers
(on select models)
Harness covers help
provide comfort to the
neck. To remove the
covers, unthread the
harness splitter plate
(see section C-7), remove
covers, and rethread
harness.
Reverse to replace harness
covers.
D. General Vehicle Installation
32
D-2 Vehicle Seating Position
Some seating positions in your vehicle may not be safe for
this child restraint. Some vehicles do not have a seating
position that can be used safely with this child restraint. If
you are not sure where to place the child restraint in your
vehicle, consult your vehicle’s owner manual or contact Dorel
Juvenile Group Consumer Relations Department.
Use the child restraint only on vehicle seats
that face forward. Do not use on seats that face
the sides or rear of the vehicle.
Safety Tip:
Children are safer when
properly restrained in
rear seating positions
than in the front seating
positions.
According to National Highway Traffic
Safety Administration information, children
in rear seating positions are statistically
safer, whether you have airbags, advanced
airbags, or no airbags at all.
31
Vehicle Belts
If LATCH is not an option,
you must use the vehicle
seat belt system to install
the child restraint. There
are some vehicle belts that
will not work with a child
restraint or will require special attention.
See next page and check your vehicle’s owner manual for
specific instructions.
The LATCH System
LATCH (Lower Anchors and
Tethers for CHildren) is a
universal system for installing
child restraints without using
vehicle seat belts.
The LATCH system can ONLY
be used in vehicles that have
the LATCH anchor bars installed and designated LATCH seating
positions. Most vehicles manufactured after September 2002 are
equipped with LATCH.
Check your vehicle’s owner manual to see which seating
positions may be equipped with the LATCH system.
D-3 Choosing LATCH or Vehicle Belts
LATCH Anchor Bars
Do not use both the LATCH belt and vehicle
belt at the same time.
D. General Vehicle Installation
33 34
D-4 Knowing Your Vehicle Belts
Review your vehicle’s owner manual for vehicle seat belt use
with child restraints. This is your best source for information
concerning your vehicle.
Not all vehicle belts will work with this child restraint. This
child restraint must be tightly locked in place at all times,
during travel. You must determine if your vehicles belts are
compatible with this child restraint.
Vehicle Belts
• Automatic/Passive vehicle seat belts
You MUST have a lap belt to install any child restraint. An
automatic (passive) shoulder belt may or may not have a
separate lap belt. Consult your vehicle’s owner manual.
• Vehicle belts in center of the door
or side panel
You must move the child restraint to
another seating location. Consult your
vehicle’s owner manual.
• Vehicle belts that are in front of
the seat bight
You may need to move the child
restraint to another seating location.
Consult your vehicle’s owner manual.
Do Not Use with inflatable seat belts
You may need to move the child restraint to another seating
location or use LATCH belts only.
• ELR (Emergency Locking Retractor) vehicle belts
These lap and shoulder belts only lock
in a sudden stop or crash, and do not
properly secure a child restraint alone.
Consult your vehicle’s owner manual.
To learn if you have this type of belt,
gently pull the belt all the way out of the retractor (spool), let it
return several inches, then pull on it again. If it moves freely,
it is an ELR belt. If it is locked and will not allow any more
belt to come out, it is a switchable retractor.
ELR lap-only belts MUST NOT be used with
this child restraint.
• Switchable retractor
These belts switch from ELR to ALR (Automatic Locking
Retractor). You must have the vehicle belts in the locking
mode to use them. Follow the instructions in the
installation sections.
• ALR (Automatic Locking Retractor)
These belts lock after pulling the webbing out and letting the
belt go back into the retractor an inch or two. Follow the
instructions in the installation sections.
Vehicle Latch Plates • Check the Latch Plates
Grasp the tongue portion of
the latch plate (the part that
goes inside the buckle) and
pull straight out, inline with
the lap belt. If the latch
plate does not slide up and
down the vehicle belt, you
have a locking latch plate.
You should not need to use
a locking clip. Consult your
vehicle’s owner manual.
If the latch plate slides up and down on the belt, and you have
an ELR retractor, you MUST use a locking clip to install the
child restraint. You may not need to use the locking clip with
a switchable or ALR retractor. Consult your vehicle’s owner
manual.
Locking
Latch
Plate
Sliding
Latch
Plate
If you have an ELR lap and shoulder belt, review the “Vehicle
Latch Plate” section to see if you need a locking clip.
E. Installing Forward Facing
35 36
This restraint is certified
for aircraft use only when
used with the internal
harness.
This child restraint is
not certified for use in
aircraft when used as a belt-positioning booster,
because aircraft seats do not have shoulder belts.
Use only on forward-facing aircraft seats. Follow
instructions for vehicle installation.
Contact the airline their specific policies.
D-5 Aircraft Information E-1 Preparing to Install Forward Facing
Lap Belt
up to 65 lbs.
(29 kg)
LATCH Belt
up to 40 lbs.
(18 kg)
Lap/Shoulder
Belt
up to 65 lbs.
(29 kg)
22-65 lbs (10.1-29 kg) and 34-49 in. (85.1-125 cm)
and at least 1 Year Old.
Forward Facing using 5-point harness
Never place a child less than one-year old or
weighing less than 22 lbs. forward-facing.
E. Installing Forward-Facing
40
39
1. Place Child Restraint in
the Back Seat
Forward Facing
Place child restraint flush
against the vehicle seat
back forward facing.
Kickstand MUST be folded
out in order to use this
seat.
Hook LATCH to
Vehicle Anchor
Fasten one LATCH belt hook to
the anchor in the vehicle seat
bight. Repeat for other side of
child restraint.
2.
Installation Tip:
Loosely attach the tether
hook before attaching
the LATCH belt. Consult
vehicle’s owner manual
for specific location.
Tighten LATCH Belt
Push down firmly while pulling
up on the LATCH belt to
tighten belt.
3.
Tighten Top
Anchorage Strap
Push firmly on the back of
the seat and tighten top
anchorage strap.
4.
Check Vehicle Belt
Tightness
Grasp the child restraint at
the belt path with one hand.
Push and pull the child
restraint from side to side,
forward and back. The child
restraint should not move
more than 1 in (2.5 cm).
NOTE: If it moves more
than 1 in (2.5 cm), try
reinstalling the child
restraint or try another
seating location.
5.
To Remove LATCH Belt
From Vehicle Anchor
Press down firmly on adjuster
side of child restraint and
press release button to
release tension. Unhook
LATCH from bar by squeezing
spring lever and twist hook.
6. Secure Child in the
Restraint
Do not use this seat with the kickstand folded
in.
E. Installing Forward Facing
42
41
E-5 Installing Forward Facing
With Vehicle Belts
Do not use the LATCH system along with the
vehicle belt. Store LATCH belts when using the
vehicle belts.
Check the vehicle belt before each use. Use
only if the belt is tightened properly and
securely.
Failure to follow these warnings can result in
serious injury or death.
Store LATCH
1.
Place Child Restraint
in Vehicle
Forward Facing
Place child restraint flush
against the back of the
vehicle seat forward
facing in the back seat.
Kickstand MUST be folded
out in order to use this
seat.
2.
NOTE: Review the section D-4 and your vehicle’s owner
manual to determine what kind of vehicle belts you have.
Thread Vehicle Belt
Thread the vehicle lap
or lap/shoulder belt
combination through the
forward-facing belt path
and out the other side.
Buckle vehicle belt.
3.
Tighten Vehicle Belt
Push down firmly on the
child restraint and pull on
the shoulder belt or lap belt
adjuster to tighten.
With a switchable retractor,
pull the shoulder belt all
the way out to switch the
retractor into the ALR mode
before tightening. Feed the
slack back into the retractor
while tightening.
4.
Installation Tip:
Loosely attach
the tether hook
before threading
the vehicle belt.
Consult vehicle’s
owner manual for
specific location.
Do not use this seat with the kickstand folded
in.
46
45
1.
2.
Store LATCH
Store Top Anchorage
Strap (Tether)
F-2 Installing Using the Lap and
Shoulder Belts
DO NOT use a locking clip when using this seat as a belt-
positioning booster.
3. Place Child Restraint
in Vehicle
Forward Facing
Place child restraint
flush against the back of
the vehicle seat forward
facing.
Tuck loose end of the
harness tightening strap
under the child restraint.
Place Child in Seat
Child should sit with their back
and bottom flat against the
back of the child restraint.
4.
Position Headrest
Adjust the headrest so that
the middle of the child’s
head is below the top of the
headrest.
5.
To Adjust Headrest
Height
Squeeze the metal bar on
the back of the seat. Move
headrest adjuster up or
down to the position that
correctly fits your child.
Release bar into slot to lock.
Make sure headrest locks
into place.
6.
F. Installing Belt-Positioning Booster
Check Vehicle Belt
Tightness
Grasp the child restraint at
the vehicle belt path with one
hand. Push and pull the base
from side to side, forward
and back. The child restraint
should not move more than 1
in. (2.5 cm).
NOTE: If restraint moves more
than 1 in. (2.5 cm), try reinstalling the child restraint or try
another seating location.
Rebuckle Belt
Attach Top Anchorage
Strap (Tether)
6.
6.
7.
52
51
Warranty
Dorel Juvenile Group, Inc. (DJG) warrants this product to the
original retail purchaser as follows:
This product is warranted against defective materials or
workmanship for one year from the date of original purchase.
An original receipt is required to validate your warranty.
DJG will, at its option, provide replacement parts or replace this
product. DJG reserves the right to substitute if the part or model
has been discontinued.
To make a claim under this warranty you may contact us at www.
djgusa.com, fax us at 1-800-207-8182 24 hours a day, write to
DJG, Consumer Relations Department, P. O. Box 2609, Columbus,
IN 47202-2609, or call 1-800-544-1108 from 8:00 a.m. to 6:00
p.m. EST Monday through Thursday and from 8:00 a.m. to 4:30
p.m. on Friday. Proof of purchase is required and shipping
charges are the responsibility of the consumer.
Warranty Limitations:
This warranty does not include damages which arise from misuse
or abuse of this product.
Limitation of Damages:
The warranty and remedies as set forth are exclusive and in lieu
of all others, oral or written, expressed or implied. In no event
will DJG or the dealer selling this product be liable to you for any
damages, including incidental or consequential damages, arising
out of the use or inability to use this product.
Limitation of warranties and other warranty terms and
state law rights:
Any implied warranties, including implied warranties of the
merchantability and fitness for a particular purpose, shall be
limited to the duration and terms of the express written warranty.
Some states do not allow limitations as to how long an implied
warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to
you. This warranty gives you specific legal rights, and you may
have other rights, which vary from state to state. Neither DJG nor
the dealer selling this product authorized any person to create for
it any other warranty, obligation, or liability in connection with this
product.
53 54
Complete the form below. Your model number with color code and
manufacturer date code MUST be included on the form to ensure
proper replacement parts. Your model number with color code and
the date code can be found on a sticker on the side of child restraint.
Payment in U.S. dollars must accompany your order. Choose parts
needed from the list on the next page.
Return the form with payment to:
Dorel Juvenile Group, Inc.
Consumer Relations Department
P.O. Box 2609
Columbus, IN 47202-2609
Fax orders to: 1-800-207-8182
Please make money orders payable to Dorel Juvenile Group, Inc. Fill
in the area below to charge to Visa or Mastercard. We do not accept
cash, personal checks, or Discover Card. All outside of U.S. and
Canada MUST use credit card.
Ship To (Please Print): _________________________________
Name: _____________________________________________
Address: ___________________________________________
City: ______________________________________________
State/Province: __________________________ Zip _________
Telephone: _________________________________________
Email Address: ______________________________________
Replacement Parts Order Form
We MUST have this information to process your order:
Model Number (8 to 9 characters): _____________________
Manufacture Date (mm/dd/yyyy): ______________________
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Safety 1st Summit 65 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Safety 1st Summit 65 in the language / languages: English as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info