Do not insert your fingers into the openings in the fan housing and hold the fan.
If the cutter bar should be turned during cleaning, there is a risk of fingers being
squashed between fan and fan housing.
IMPORTANT
Never use high-pressure cleaners or a normal water jet to clean the drive area,
engine parts (such as ignition system, carburettor etc.), seals and bearing points.
Damage or expensive repairs can be the consequence of such action.
Pos: 20.8 /Innenteil/Pflege und Wartung des Mähers/1.1 Aufbewahrung @ 0\mod_1115363938281_1521.docx @ 1810 @ 2 @ 1
Storage
Pos: 20.9 /Innenteil/Pflege und Wartung des Mähers/Aufbewahrung Text @ 0\mod_1115364661953_1521.docx @ 1824 @ @ 1
Always keep the machine in a clean condition in a closed, dry room out of reach of
children. Always allow the engine to cool down before you store the machine in a
closed room.
Pos: 20.10 /Innenteil/Pflege und Wartung des Mähers/1.1 Umklappen des Führungsholmes (Abbildung A1) @ 1\mod_1132311550241_1521.docx @ 5669 @ 2 @ 1
Collapsing the handle (Illustration A1 )
Pos: 20.11 /Innenteil/Pflege und Wartung des Mähers/Umklappen des Führungsholmes Text 43er, 47er neu @ 13\mod_1280395594668_1521.docx @ 110557 @ @ 1
– To save storage space or for transportation, loosen the four wing nuts so that the
guide tube can be folded together without resistance in a Z-shape above the
engine A1 .
The toothed plastic adaptations on the bottom bar end must snap out of the
cut-out on the housing.
– Do not kink nor squeeze the throttle cables in the process.
CAUTION
When folding the bar for transport and storage purposes, when loosening the
wing nuts and snapping the toothed plastic adaptations from the cut-out on the
housing, it is possible that unintentional upsetting of the bar may occur. In
addition, this may result in crushed points between the top and bottom part of
the bar as well as the housing. This may result in a risk of injury!
Pos: 20.12 /Innenteil/Pflege und Wartung des Mähers/1.1 Transport und Sicherung des Gerätes (Abbildung N ) @ 10\mod_1250083705506_1521.docx @ 85935 @ 2 @ 1
Transporting and securing the equipment (Illustration N )
Pos: 20.13 /Innenteil/Pflege und Wartung des Mähers/Transport und Sicherung Text 36er,40er,43er, Elektro+Benzin @ 32\mod_1408515936740_1521.docx @ 239661 @ @ 1
– If the equipment has to be carried, do not hold the ejection flap. Hold the carrying
handle at the front and at the back N .
– Transport the equipment in an upright position.
– Park the means of transport on level ground so that the equipment cannot roll
away before it is secured.
– Remove the collecting bag and secure it separately during transport
– Secure the equipment with approved load-securing devices (e.g. tie-down straps
with clamping elements) on or inside the vehicle. Tie-down straps are belt bands
made of synthetic fibres. Every tie-down strap is marked with a label. The label
contains important details for application. The information on this label must be
heeded when using the tie-down strap.
– For loaded goods that can roll, we recommend using direct strapping with four
lashing straps. Secure the wheels of the equipment in such a way that it does not
move during transportation.
NOTE
Do not tighten the belts too firmly. Fixing the equipment too firmly can cause
damage.
Pos: 20.14 /Innenteil/Pflege und Wartung des Mähers/1.1 Wartung des Messerbalkens @ 0\mod_1115365509765_1521.docx @ 1823 @ 2 @ 1
Maintenance of the blade
Pos: 20.15 /Innenteil/Pflege und Wartung des Mähers/Wartung des Messerbalkens Text Benzin @ 19\mod_1346246117815_1521.docx @ 149465 @ @ 1
A sharp blade guarantees optimum cutting performance. Before you start mowing,
always check the condition and firm attachment of the cutting blade. The blade
attachment screw must always be tightened by an authorised workshop. If the blade
screw is too tight or too loose, the blade coupling and cutter bar can become damaged
or loose which can lead to serious injuries. A worn or damaged blade must always be
replaced.
Pos: 20.16 /Innenteil/Pflege und Wartung des Mähers/1.1 Nachschleifen und Auswuchten des Messerbalkens (Abbildung Q) @ 0\mod_1115365616312_1521.docx @ 1815 @ 2 @ 1
Sharpening and balancing the blade (Illustration Q )
Pos: 20.17 /Innenteil/Pflege und Wartung des Mähers/Nachschleifen und Auswuchten des Messerbalkens Hinweis Benzin @ 0\mod_1115618908515_1521.docx @ 1839 @ @ 1
WARNING
The sharpening and balancing of the blade should be carried out only by an
authorized specialist workshop. An improperly sharpened or unbalanced blade
can cause severe vibrations, and damage the lawnmower.
Pos: 20.18 /Innenteil/Pflege und Wartung des Mähers/Nachschleifen und Auswuchten des Messerbalkens neu Text @ 12\mod_1257776115383_1521.docx @ 98647 @ @ 1
The cutting edges of the cutting blade may be grinded only until the respective value
(see illustration Q ) or the marking (1) on the cutting blade (ring) has been reached.
Attention! Observe the grinding angle of 30°.
Your professional workshop can check this value - (grinding limit) for you!
Pos: 20.19 /Innenteil/Pflege und Wartung des Mähers/Nachschleifenund Auswuchten des Messerbalkens Hinweis Markierung @ 9\mod_1228810807409_1521.docx @ 70873 @ @ 1
WARNING
A blade by which the wear limit (marking) has been exceeded can break off and
spin away; this can cause severe injuries.
Pos: 20.20 /Innenteil/Pflege und Wartung des Mähers/1.1 Auswechseln des Messerbalkens @ 3\mod_1157368508411_1521.docx @ 18733 @ 2 @ 1
Replacing the blade
Pos: 20.21 /Innenteil/Pflege und Wartung des Mähers/Auswechseln des Messerbalkens Hinweis Benzin neu @ 19\mod_1346311701802_1521.docx @ 153192 @ @ 1
WARNING
The cutting blade bar must always be replaced by an authorised workshop. A
wrongly assembled cutting blade coupling or a blade screw that is tightened too
tightly or too loosely can allow the cutting blade bar to become loose and cause
severe injuries.
Pos: 20.22 /Innenteil/Pflege und Wartung des Mähers/Auswechseln des Messerbalkens Text Elektro+Benzin neu @ 26\mod_1377172735519_1521.docx @ 191162 @ @ 1
– Only use genuine cutter bars for replacement. Non-equivalent spare parts can
damage the machine and are a safety hazard.
– Replacement cutting tool must be marked permanently with the name and/or
company logo of the manufacturer or supplier and the part number.
Pos: 20.23 /Innenteil/Pflege und Wartung des Mähers/1.1 Wartung der Räder (Abbildung S) @ 0\mod_1125651856935_1521.docx @ 1819 @ 2 @ 1
Servicing the wheels (Illustration S )
Pos: 20.24 /Innenteil/Beschreibung der Bauteile/43-COMPACT (SA1741), 43-COMPACT E (SA1461), R43 (SA1406) @ 44\mod_1469178895436_0.docx @ 50 5375 @ @ 1
43-COMPACT (SA1741), 43-COMPACT E (SA1461), R43 (SA1406)
Pos: 20.25 /Innenteil/Pflege und Wartung des Mähers/Wartung der Räder Text Elektro,40er,43er o.A .,52-SA Konuskugellager fetten @ 44\mod_1469181710903_1521.docx @ 505458 @ @ 1
Lubricate the wheel bearings once a year or every 15-20 operating hours.
– Remove the wheel caps S .
– Use a socket wrench to loosen the hexagon nut, washer and wheels.
– After the bearings have been lubricated with roller bearing grease "KAJO-Longlife
grease LZR 2", push the wheels back in place, replace the washer, fix the hexagon
nut and tighten until the wheels can just about turn easily but without play. Replace
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Sabo R43 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Sabo R43 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.
The manual is 3,06 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
