Attaching the motor brake Bowden cable to the engine (Illustration H1 )
Pos: 13.1 3 /Innenteil /Vorbereit ende Arbeiten /Einhängen des Motor-Brems- Bowdenzuges am Motor Text 52 -S A/52-PRO S A @ 38 \mod_1439451538339_1521.docx @ 404463 @ @ 1
– Insert the elbow on the end throttle cable (1) from below, into and up to the bend of
the switching lever of the brake (2).
– Pull the moving part of the throttle cable (3) to the rear until the wire cable (4) can
be inserted from above (SA1626) or from the side (SA1649) into the cut-out (5).
– Then slide the throttle cable (3) forwards until the snap-hook (6) engages in the
cut-out (5) of the throttle cable mount.
Pos: 13.14 /Innenteil/Vorbereitende Arbeiten/Einhängen des Motor-Brems-Bowdenzuges Hinweis neue OB @ 21\mod_1350982534155_1521.docx @ 159882 @ @ 1
NOTE
After attachment of the engine-brake throttle cable, the braking function of the
safety control bar must be checked. As soon as the control bar is released, the
cutter bar must come to a standstill within three seconds. If this is not the case,
Pos: 14.4 /Innenteil/Vor der Ersten Inbetriebnahme/Allgemeine Sicherheitshinweise Benzinmäher + Text DLG @ 37\mod_1436248174398_1521.docx @ 400215 @ @ 1
Check all screw connections and the spark plug connector for a tight fit. Tighten the
screws if necessary! Attachment of the cutter bar must be checked in particular (refer
here to the chapter "Cutter bar care").
The blade attachment screw must always be tightened by an authorised workshop. If
the blade screw is too tight or too loose, the blade coupling and cutter bar can become
damaged or loose which can lead to serious injuries.
The lawn mower is equipped with a motor stop device.
Before using the equipment for the first time, make sure that the motor stop safety
control bar is working perfectly. When the control bar is released, the motor and cutter
bar must come to a standstill within three seconds.
After release, the bar must always return to the position shown in the "component
description" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the blade run-on time is longer, stop using the equipment and take it to an authorised
workshop.
Measuring run-on time
After the engine has been started, the blade rotates and a wind-like noise can be heard.
The run-on time corresponds to the duration of the wind-like noise after the engine has
been stopped, it can be measured using a stopwatch.
Pos: 14.5 /Innenteil/Vor der Ersten Inbetriebnahme/Sicherheits- und Schutzeinrichtungen ... dürfen nicht manipuliert oder deaktiviert werden!_dl_text @ 38\mod_1437988093850_1521.docx @ 402470 @ @ 1
Machine safety and protective devices must not be manipulated or disabled!
Pos: 14.6 /Innenteil/Vor der Ersten Inbetriebnahme/Darauf achten ... Schutzeinrichtungen ordnungsgemäß angebracht und nicht beschädigt sind! @ 37\mod_1436249863921_1521.docx @ 400691 @ @ 1
Make sure that all protective devices have been attached properly and are not
damaged.
Pos: 14.7 /Innenteil/Vor der Ersten Inbetriebnahme/1.1 Öl einfüllen (Abbildung Y1 ) @ 0\mod_1115210961078_1521.docx @ 1711 @ 2 @ 1
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Sabo 52-PRO SA at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Sabo 52-PRO SA in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.
The manual is 3,04 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
