733431
9
Zoom out
Zoom in
Previous page
1/28
Next page
RBC36X26E
RBC36X26E
ORIGINAL INSTRUCTIONS
Pressure Washer
RPW150-G
Important!
It is essential that you read the instructions in this manual before assembling,
operating, and maintaining the product.
Subject to technical modification.
1
Safety, performance, and dependability have been given
top priority in the design of your pressure washer.
INTENDED USE
The pressure washer is only intended for use outdoors. For
safety reasons the product must be adequately controlled
by using two-handed operation.
The product is designed for home or domestic use. It is
intended to clean machines, vehicles, buildings, oors,
tools, facades, terraces, oors, and concrete walkways by
removal of stubborn dirt using clean water with or without
cleaning detergent.
It should be used in dry and well-illuminated conditions.
Do not use the product for any other purpose.
WARNING
The product is designed for use with a neutral cleaning
agent supplied or recommended by the manufacturer.
The use of other cleaning agents or chemicals may
adversely affect the safety of the product.
GENERAL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, re, and/or serious injury.
CAUTION
The product must not be used on the drinking water
supply without a backow preventer being installed.
Water owing through a backow preventer is considered
non-drinkable. Always observe the regulations of your
local water utility company when connecting the product
to a water supply line.
The product is not intended for use by children or
persons with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge.
Children should be adequately supervised to ensure
they do not play with the product.
Wear a complete personal protective equipment when
operating the product, such as boots, safety gloves,
safety helmets with visor, and hearing protection. Use
high-impact visors only with liquid splash protection.
WARNING
Do not use the product when people are within range,
unless they wear protective clothing.
To reduce the risk of injury, keep children and visitors
away. All visitors should wear safety glasses and be
kept at a safe distance from the work area.
Inspect the safety devices, such as safety valves, flow
switches, and pressure switches to check if they are in
good working condition. Make sure all safety devices
are operating properly before each use, such as:
On/off switch
The on/off switch prevents unintentional
operation of the product.
Trigger handle lock
The trigger handle lock locks the trigger and
prevents unintentional opening of the high-
pressure jet.
Total stop switch
The total stop switch prevents the permissible
working pressure from being exceeded. If the
lever on the trigger gun is released, the pressure
switch turns off the pump and the high-pressure
jet stops. If the lever is pulled, the pump turns
on again.
Overload protection
A thermal sensor protects the product from
overloading. The product will automatically shut
the power down while overheating.
Do not use the product if the important parts are
damaged, such as safety devices, high-pressure
hoses, or trigger gun.
Exercise caution when opening the trigger. Hold the
handle firmly with two hands to avoid injury when the
handle kicks back.
WARNING
During use of high pressure cleaners, aerosols may
be formed. Inhalation of aerosols can be hazardous to
health.
WARNING
Depending on the application, shielded nozzles can
be used for high-pressure cleaning, which will reduce
the emission of hydrous aerosols. However, not all
applications allow the use of such a device. If shielded
nozzles are not applicable for the protection against
aerosols, a respiratory mask of class FFP 2 or equivalent
may be needed, depending on the cleaning environment.
Always stop the product when you leave it unattended.
High-pressure jet is dangerous if misused. Do not
direct the jet to people, live electrical equipment, or the
product itself.
To avoid a risk of explosion, do not spray flammable
liquids.
Do not direct the jet against yourself or others in order
to clean clothes or footwear.
Do not use the product to clean electronic devices,
clothes, or footwear.
High-pressure hoses, fittings, and couplings are
important for the safety of the product. Use only
hoses, fittings, and couplings recommended by the
manufacturer.
2
ELECTRICAL SAFETY WARNINGS
The plug must match the outlet. Never modify the plug
in any way. Unmodified plugs and matching outlets
reduces the risk of electric shock.
Do not use the product if the power cord or other
important parts, such as safety devices, are damaged.
Only use a weather proof extension cord. Check the
extension cord before every use for damage. Always
uncoil the extension cord during the use because
coiled cords can overheat. Damaged extension cords
should not be repaired, they should be replaced with
an equivalent type.
Keep the power cord away from heat, oil, and sharp
edges.
Never touch the mains plug and the socket with wet
hands.
Inadequate extension cords can be dangerous. If an
extension cord is used, it shall be suitable for outdoor
use, and the connection has to be kept dry and off the
ground. Use a cord wheel to keep the socket at least 60
mm above the ground.
Electric power shall be supplied with a residue current
device (RCD) with a tripping current of not more than
30mA.
ADDITIONAL SAFETY WARNINGS
Some regions have regulations that restrict the use of
the product in some operations. Check with your local
authority for advice.
Before each use, check for damage. A damaged high-
pressure hose must be replaced immediately. Ensure
all connections, such as high-pressure hose and
nozzle, are secure. Unwind the hose properly so they
may not get twisted or kinked.
Do not allow children or untrained individuals to use the
product.
Before starting any cleaning operation, close doors and
windows. Clear the area to be cleaned of debris, toys,
outdoor furniture, or other objects that could create a
hazard.
Never pick up or carry the product while the motor is
running.
Do not use the product in temperatures below 0°C.
Do not use acids, alkalines, solvents, flammable
material, bleaches, or industrial grade solutions in the
product. These products can cause physical injuries to
the operator and irreversible damage to the product.
Always operate the product on a level surface.
WARNING
High-pressure jet can be dangerous if subject to misuse.
The jet must not be directed to people, animals, electrical
devices, or the product itself.
Hold the handle securely with both hands. Expect
the handle to move when the trigger is pulled due to
reaction forces. Failure to do so could cause loss of
control and injury to yourself and others.
Make sure the air in the hose and pump is released
before you turn on the product. To remove the air in
the hose and pump, connect the water supply to the
pump using a garden hose, connect the trigger handle
to pump using the high-pressure hose, disengage the
trigger handle lock, and press the trigger until there is
a steady flow.
Exercise caution to avoid slipping or falling.
Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance.
Only use accessories that are recommended by the
manufacturer. The use of improper accessories may
cause injury.
Never leave the product running unattended. Turn the
product off. Do not leave the product until it comes to
a complete stop.
Be familiar with the controls. Know how to stop the
product and bleed the pressure quickly.
Stay alert and exercise control. Watch what you are
doing and use common sense.
Do not use the product when you are tired, ill, or
under the influence of drugs, alcohol, or medication. A
moment of inattention while operating the product may
result in serious personal injury.
Do not use the product if the switch does not turn it on
and off. Any product that cannot be controlled with a
switch is dangerous and must be repaired.
Keep a minimum distance of 30 cm when cleaning
vehicles. The high-pressure jet may damage or burst
vehicle tires and/or tire valves.
Use a garden hose with a maximum length of 15 m and
minimum diameter of 12 mm (1/2 in.)
CAUTION
Water blasting any asbestos-containing material,
including an asbestos roof, is illegal.
OVERLOAD PROTECTION
A thermal sensor protects the product from overloading.
The product will automatically shut the power down while
overheating. To resume operation, disconnect the product
from the power supply, wait for about 15 min to cool down,
and reconnect the product to the power supply.
TRANSPORTATION AND STORAGE
CAUTION
Mind the weight of the product when selecting the
storage location and during transportation to prevent
accidents or injuries.
3
Stop the product, disconnect from the power supply,
and allow the product to cool down. Disconnect
the product from the water supply before storing or
transporting. Never place the product in any position
other than upright.
Remove water from all hoses and the pump, and empty
the detergent tank before storing the product.
Clean all foreign materials from the product. Store it
in a cool, frost-free, dry, and well-ventilated place that
is inaccessible to children. Keep away from corrosive
agents such as garden chemicals and de-icing salts.
Do not store outdoors.
For transportation in a vehicle, secure the product
against movement or falling to prevent injury to persons
or damage to the product.
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts,
accessories, and attachments. Failure to do so can
cause possible injury, contribute to poor performance,
and may void your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualied service
technician. For service, bring the product to an
authorised service centre. When servicing, use only
original replacement parts.
Stop the product, disconnect from the power supply,
and allow the product to cool down. Disconnect the
product from the water supply before:
cleaning the product
maintaining the product
replacing spare parts
You may make adjustments or repairs described in
this manual. For other repairs, contact an authorised
service centre.
Regularly inspect and maintain the high pressure
cleaner for safe operation. Ryobi recommends
inspecting the product every 6 months.
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
Injury caused by the high-pressure jet
Avoid pointing the high-pressure jet to people,
animals, and to yourself.
Injury caused by kickback
Always hold the handle or the trigger wand firmly
with your two hands.
Injury caused by inhalation of aerosols
Wear appropriate respiratory mask.
Injury caused by exposure to noise
Wear ear protection.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud’s Syndrome.
Symptoms may include tingling, numbness, and blanching
of the ngers, usually apparent upon exposure to cold.
Hereditary factors, exposure to cold and dampness, diet,
smoking, and work practices are all thought to contribute to
the development of these symptoms. There are measures
that can be taken by the operator to possibly reduce the
effects of vibration:
Keep your body warm in cold weather. When operating
the product, wear gloves to keep the hands and wrists
warm.
After each period of operation, exercise to increase
blood circulation.
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
SYMBOLS ON THE PRODUCT
Warning
Class II tool, double insulation
To reduce the risk of injury, user must
read and understand operator’s manual
before using this product.
Wear eye and hearing protection.
Remove plug from the mains immediately
if cable is damaged or cut.
Electrical shock hazard
4
The product is not suitable for connection
to the drinking water mains without
backow preventer.
Never point the spray wand to people,
animals, the body of the product, power
supply, or any electric appliances.
Burst hazard
Regulatory Compliance Mark (RCM).
Product meets applicable regulatory
requirements.
97
dB
81
dB
A-weighted sound pressure level at the
operator position is 81 dB.
The guaranteed sound power level
shown on this label is 97 dB.
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority or retailer
for recycling advice.
SYMBOLS IN THIS MANUAL
Wear non-slip, heavy-duty, protective
gloves when handling.
Parts or accessories sold separately
Note
Warning
The following signal words and meanings are intended to
explain the levels of risk associated with this product.
DANGER
Indicates an imminently hazardous situation, which, if
not avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not
avoided, may result in minor or moderate injury.
CAUTION
Without safety alert symbol
Indicates a situation that may result in property damage.
5
TROUBLESHOOTING
Problem Possible causes Solution
Machine refuses to
start
Machine not plugged in Plug in machine.
Defective socket Try another socket.
Defective extension cable Try without the extension cable.
Fluctuating pressure Pump sucking air Check that hoses and connections are air tight.
Valves dirty, worn out or stuck Clean and replace or refer to local distributor .
Pump seals worn out Clean and replace or refer to local distributor.
Motor buzzes Low voltage or low temperature Activate the trigger of the spay handle.
Machine stops Incorrect mains voltage Check that the mains voltage corresponds to specication
on the model tag.
Thermal sensor activated Leave the washer for 15 minutes to cool down.
Nozzle partially blocked Clean the nozzle.
Machine pulsating Air in inlet hose/pump Allow the product to run with open trigger until regular
working pressure resumes.
Inadequate supply of mains
water
Check that the water supply corresponds to the specications
required (see model tag). Avoid using long, thin hoses.
Nozzle partially blocked Clean the nozzle.
Water lter blocked Clean the lter.
Hose kinked Straighten out hose.
Machine often starts
and stops by itself
Pump/spray handle is leaking Wait for the pump, hoses, or other accessory to thaw.
Machine starts, but
no water comes out
Pump/hoses or accessory frozen Wait for pump/hoses or accessory to thaw.
No water supply Connect the water inlet port to a water supply.
Water lter blocked Clean the lter.
Nozzle blocked Clean the nozzle.
6
UNPACKING
x 1 x 1
x 1
x 1
x 1
x 1
x 1
x 1 x 1
x 1
x 1
x 1
7
Know your product
KNOW YOUR PRODUCT
19
18
17
16
15
14
12 11 10 9 8
7
6
5
4
3
2
1
13
1. Trigger gun lock
2. Trigger
3. Hose reel handle
4. Power cord holder
5. Power cord
6. Soap tank
7. Water inlet port
8. Water inlet coupler with filter
9. Surface cleaner wand
10. Surface cleaner housing
11. Spray nozzle wand
12. Spray nozzle
13. Turbo nozzle
14. Turbo nozzle wand
15. On/off switch
16. Trigger handle holder
17. High pressure hose
18. High pressure hose reel
19. Handle
8
GETTING STARTED
2
3
1
1 2
1
2
5
1
2
3
4
6
9
GETTING STARTEDGETTING STARTED
2
1
9
10
3
4
1
2
2
1
3 4
1
2
7
1
2
8
10
11
OVERVIEW
p.12 p.13 p.15
p.20p.16 p.19
12
OPERATION
1
2
1
2
2
4
1
3
13
OPERATION
1
2
2
1
14
OPERATION
5
4
3
15
OPERATION
1
2
1
2
2
3
1
4
16
OPERATION
2
1
3
2
1
17
OPERATION
7
1
2
5
4
6
18
OPERATION
1
2
8
19
MAINTENANCE
2
1
20
STORAGE
1
2
2
1
1
3
2
4
21
STORAGE
2
1
2
1
5
6
7
22
STORAGE
8
20170707v1d9
23
OPERATION
PRODUCT SPECIFICATIONS
Pressure washer
Model RPW150-G
Rated voltage
220 - 240V
Frequency
50 Hz
Power
2000W
Hose length 8m
Dilution ratio 10%
Maximum pressure
15MPa (150bar/2200psi)
Rated pressure
11MPa (110bar/1600psi)
Degree of protection
IPX5
Rated ow
6.67 L/min
Max. ow
7.2 L/min
Max. inlet water pressure
0.7 MPa
Detergent tank
1.2L
Power cord length
5m
Sound pressure level (L
PA
)
(in accordance with EN
60335-2-79)
81.3 db
Uncertainty
1.7 db
Sound power level (L
WA
)
(in accordance with EN
60335-2-79)
96.7 db
Uncertainty
1.7 db
Vibration value (in
accordance with EN
60335-2-79)
<2.5 ms
2
Weight
12.3 kg
099903021064-01
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149
Melbourne, Australia
Techtronic Industries N.Z. Limited
2 Landing Drive, Mangere
Auckland, 2022, New Zealand
Imported by:
9


Need help? Post your question in this forum.

Forumrules
1

Forum

ryobi-rpw150-g
  • My Ryobi RPW150-G will run at full pressure for about 10 seconds then stop, I release the trigger and engage again and the same thing happens.
    The in line filter is clean and there is ample water pressure.
    I have used my sons Ryobi cleaner and it works fine.
    Any ideas
    Brian Submitted on 21-11-2022 at 04:16

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi RPW150-G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi RPW150-G in the language / languages: English as an attachment in your email.

The manual is 5,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info