491257
17
Zoom out
Zoom in
Previous page
1/156
Next page
PARTICULAR REQUIREMENTS FOR
CIRCULAR SAWS
Adjust the riving knife as described in this
instruction manual . Incorrect spacing, positioning
and alignment can make the riving knife ineffective in
preventing kickback.
Always use the riving knife except when plunge
cutting. Riving knife must be replaced after plunge
cutting. Riving knife causes interference during
plunge cutting and can create kickback.
For the riving knife to work, it must be engaged in
the workpiece. The riving knife is ineffective in
preventing kickback during short cuts.
Do not operate the saw if riving knife is bent. Even
a light interference can slow the closing rate of a
guard.
DESCRIPTION
1. Spindle lock button 14. Depth of cut
2. Hex-head bolt 15. Depth scale
3. Spanner 16. Bevel adjustment knob
4. Outer blade washer 17. Bevel scale
5. Lower guard 18. Trigger switch
6. Lower guard lever 19.Safety button
7. Upper guard 20. Line guide
8. Blade 21. Depth adjustment lug
9. Inner blade washer 22. Live Tool indicator
10. Dust nozzle 23. Laser guide button
11. Riving knife 24. Laser guide
12. Depth lock knob 25. LED button
13. Base plate 26. LED light
SPECIFICATIONS
Blade diameter 190 mm
EWS-1266 EWS-1366
Voltage 230V 110V/230V
Input 1,250 W 1,250 W/1,350 W
No load speed 4,500 min
-1
4,500 min
-1
Bore size 16 mm 16 mm
Blade size 190mm 190 mm
Cutting capacity
at 0
0
66 mm 66 mm
at 45
0
38 mm 38 mm
Bevel scale 0 – 45° 0 – 45°
Cord length 4 m 3m/4 m
INSTRUCTIONS FOR SAFE HANDLING
The maximum permissible system impedance:
Zmax for EWS-1266 is 0.245 Zref & Zmax for EWS-1366 is
0.252 Zref.
If in doubt, please verify with your local energy-utilitythat the
AC outlets in your area do not exceed theabobe values.
STANDARD ACCESSORIES
Saw blade, Parallel fence, Spanner.
APPLICATION
Sawing wood.
NOISE BUILD-UP
Noise (sound pressure level) in the workplace can
exceed 85 dB. In this case, sound insulation and
hearing protection measures must be taken by the
operator.
ASSEMBLY INSTRUCTIONS
BE SURE TO DISCONNECT THE TOOL FROM
THE POWER SUPPLY BEFORE ATTACHING
OR REMOVING THE SAW BLADE. BE SURE THAT
THE TEETH OF THE SAW BLADE ARE POINTING
UPWARD AT THE FRONT OF THE TOOL.
ATTACHING AND REMOVING
THE BLADE (FIGURES 2, 3, 4, AND 5)
ATTACHING THE BLADE
1. Pressing the spindle lock button (1), turn the hex-
head bolt (2) with the spanner (3) until the spindle
locks. (Fig.2)
2. Loosen the hex-head bolt by turning the spanner
anticlockwise while pressing the spindle lock button.
(Fig.2)
3. Remove the hex-head bolt and the outer blade
washer (4). (Fig. 2)
4. Retract the lower guard (5) back with the lower guard
lever (6) as far as possible under the upper guard
(7). (Fig. 3)
5. Then, attach the saw blade (8) against the inner blade
washer (9) on the spindle. Then fit the outer blade
washer and the hex-head bolt. (Fig. 3 and 4)
11
GB
English
F D E I P NL S DK N FIN GR H CZ RUS PL
RO
SLO TR
HR
EWS-1266EWS-1366(EU).qxd 11/24/2004 4:49 PM Page 11
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi EWS-1366 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi EWS-1366 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info