Manual Ryobi ejs 500 qeo (page 15 of 142) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

383096

Zoom out

Zoom in

1/142

OPERATION

GENERAL CUTTING (Fig. 5)

Rest the front of the saw base on the workpiece and align

cutting edge of the blade with the line on your workpiece.

Make sure the power cord is out of the way of saw blade

and not in the line of cut. Start your saw and move it

forward on the work surface. Apply downward pressure to

keep the saw steady and only enough forward pressure

to keep the blade cutting.

DO NOT FORCE YOUR SAW

Forcing your saw may overheat the motor and

break saw blades.

ORBITAL MOTION (Fig. 5)

The blade of your saw cuts in orbital motion. This feature

is adjustable and provides faster and more efficient

cutting. With orbital motion the blade cuts through your

work in the upstroke but does not drag across your work

in the downstroke.

■ Higher settings (H) should be used when fast cutting

in soft material.

■ Lower (L) settings should be used when cutting

materials with more resistance.

STRAIGHT CUT (Fig. 5)

Astraight cut can be made by clamping a piece of wood or

straightedge to the workpiece and guiding the edge of your

saw against it. Make the cut from one direction only, do not

cut halfway to complete the cut from the opposite end.

SCROLL CUTTING (Fig. 6)

Scroll cuts can be made with your saw by guiding the

direction of the cut with applied pressure on the handle.

WARNING

Excessive side pressure to the blade could result in

broken blades or damage to the material being cut.

ANGLE CUTTING (Bevel Cutting) (Fig. 7)

Bevel cutting angles may be adjusted from 0° to 45° right

or left. Angles for cuts from 0° to 45° in 15° increments

are marked on a scale on both the left and right side of

the base.

The use of a protractor is recommended when accurate

cuts are required.

Adjusting the angle – EJS-600QEO only

■ Release the bevel lock lever (10) until the base can

be moved.

■ Slide base forward slightly to release the base from

the tab on the motor housing.

■ Align the mark on the base of the desired angle with

the edge of the motor housing.

■ Once the desired angle is reached, slide the base

back until the tab on the motor housing aligns with the

appropriate notch on the rear of the base.

■ Push the bevel lock lever back to secure the base.

Adjusting the angle – EJS-500QEO only

■ Loosen the base retaining screws with the wrench

(supplied) until the base can be moved.

■ Slide base forward slightly to release the base from

the tab on the motor housing.

■ Align the mark on the base of the desired angle with

the edge of the motor housing.

■ Once the desired angle is reached, slide the base

back until the tab on the motor housing aligns with the

appropriate notch on the rear of the base.

■ Re-tighten the base retaining screws with the wrench

(supplied) to secure the base.

TO MAKE A PLUNGE CUT (Fig. 8)

WARNING

To avoid loss of control, broken blades, or

damage to the material being cut, always use

extreme caution when making plunge cuts.

We do not recommend plunge cutting on

materials other than wood.

■ Mark the line of cut clearly on the workpiece.

■ Set the cutting angle at 0°.

■ Tilt your saw forward so that it rests on the front edge

of the base and blade will not come in contact with the

workpiece when the saw is turned on.

■ Make sure the blade is inside the area

to be cut.

■ Start your saw by using high speed and slowly lower

the blade into the workpiece until the blade cuts

through the wood.

■ Continue lowering the blade into the workpiece until

the base rests flat on the work surface, then move the

saw forward to complete the cut.

■ Use only the 7 teeth per inch blade for this type of cut.

English

F D E I P NL S DK N FIN GR H CZ RUS PL

SLO TR

EJS-500-600QEO_20 lgs 22/01/06 17:49 Page 11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi ejs 500 qeo in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ryobi ejs 500 qeo Manual

Product: