Manual Ryobi cmd 1202 (page 14 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

388730

Zoom out

Zoom in

1/116

OPERATION

IMPORTANT INFORMATION FOR RECHARGING HOT

BATTERIES

When using your tool continuously, the batteries in your

battery pack will become hot. You should let a hot battery

pack cool down for approximately 30 minutes before

attempting to recharge.

TO INSTALL BATTERY PACK

■ Lock switch trigger on your drill by placing the

direction of rotation selector in center position.

See Figure 6.

■ Place battery pack in your drill. Align raised rib on

battery pack with groove inside drill.

See Figure 2.

■ Make sure the latches on battery pack snap in place

and battery pack is secured in drill before beginning

operation.

TO REMOVE BATTERY PACK

■ Lock switch trigger on your drill by placing the

direction of rotation selector in center position.

See Figure 6.

■ Locate latches of battery pack and depress to release

battery pack from your drill.

See Figure 2.

■ Remove battery pack from your drill.

ADJUSTING THE AUXILIARY HANDLE

(For CMI-1202/1442/1802)

See Figure 3.

Follow these steps to adjust the auxiliary handle.

■ Loosen the auxiliary handle by turning the knob

counterclockwise.

■ Rotate the auxiliary handle to the desired location.

■ Tighten the auxiliary handle securely by turning the

knob clockwise.

ADJUSTING THE DEPTH GAUGE ROD

(For CMI-1202/1442/1802)

See Figure 4.

Follow these steps to adjust the depth gauge rod.

■ Lock the trigger switch by placing the rotation selector

in the center position.

■ Loosen the auxiliary handle by turning the knob

counterclockwise.

■ Adjust the depth gauge rod so that the drill bit

extends beyond the end of the rod to the required

drilling depth.

■ Tighten the auxiliary handle by turning the knob

clockwise.

ADJUSTING THE TORQUE

See Figure 5.

The tool is equipped with an adjustable torque clutch for

driving different types of screws into different materials.

Adjust the torque as necessary.

(For CMI-1202/1442/1802)

We recommend that you use carbide-tipped bits and

select impact mode when drilling in hard material such as

brick, tile, concrete, etc.

CAUTION

The impact drill is not designed for reverse

hammering. Failure to obey this caution may

result in property damage.

SWITCH

See Figure 6.

■ To turn your drill ON, depress the switch trigger.

■ To turn it OFF, release the switch trigger.

VARIABLE SPEED

This tool has a variable speed switch that delivers higher

speed and torque with increased trigger pressure. Speed

is controlled by the amount of switch trigger depression.

SWITCH LOCK

See Figure 6.

The switch trigger can be locked in the OFF position.

This feature can be used to prevent the possibility of

accidental starting when not in use. To lock switch trigger,

place the direction of rotation selector (Forward/Reverse

Selector) in center position.

Note: When selector is in center position, switch trigger

is locked.

REVERSIBLE

See Figure 6.

This tool has the feature of being reversible. The direction

of rotation is controlled by a selector located above the

switch trigger. With the drill held in normal operating

position, the direction of rotation selector should be

positioned to the left of the switch for drilling. The drilling

direction is reversed when the selector is to the right of

the switch. When the selector is in center position, the

switch trigger is locked. To stop, release switch trigger and

allow the chuck to come to a complete stop.

F D E

English

I P NL S DK N FIN GR H CZ RUS RO PL

960001208-02 12/23/03 11:41 AM Page 10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi cmd 1202 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ryobi cmd 1202 Manual

Product: