Manual Ryobi cmd 1202 (page 13 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

388730

Zoom out

Zoom in

1/116

F D E

English

I P NL S DK N FIN GR H CZ RUS RO PL

CHARGER SAFETY

a. That pins on plug of extension cord are the same

number, size and shape as those of plug on charger.

b. That extension cord is properly wired and in good

electrical condition.

■ Do not operate charger with a damaged cord or plug.

If damaged, have it replaced immediately by a

qualified serviceman.

■ Do not operate charger if it has received a sharp

blow, been dropped, or otherwise damaged in any

way; take it to a qualified serviceman.

■ Do not disassemble charger; take it to a qualified

serviceman when service or repair is required.

Incorrect reassembly may result in a risk of electric

shock or fire.

■ To reduce risk of electric shock, unplug the charger

from outlet before attempting any maintenance or

cleaning. Turning off controls will not reduce this risk.

■ Disconnect charger from power supply when not in use.

■ Risk of electric shock. Do not touch uninsulated portion

of output connector or uninsulated battery terminal.

■ Save these instructions. Refer to them frequently and

use them to instruct others who may use this unit.

If you loan someone this unit, loan them these

instructions also.

DESCRIPTION

See Figure 1-9.

1. Keyless chuck

2. Switch trigger

3. Direction of rotation selector (Forward/Reverse)

4. Screwdriver bits

5 . Battery pack

6. Battery indicator

7. Latches

8. Depress latches to release battery pack

9. Auxiliary Handle(For CMI-1202/1442/1802)

10. To Tighten

11. To Loosen

12. Drill bit

13. Depth Gauge Rod(For CMI-1202/1442/1802)

14. Drilling Depth

15. To Decrease torque

16. To Increase torque

17. Torque adjusting Ring

18. Drill mode

19. Impact mode (For CMI-1202/1442/1802)

20. Reverse

21. Forward

22. Chuck jaws

23. Unlock (release)

24. Lock (tighten)

25. High Speed

26. Low Speed

27. Battery Charger

28. Green Light

29. Red Light

OPERATION

LED FUNCTION OF CHARGER

See Figure 9.

LED WILL BE ON TO INDICATE STATUS OF CHARGER

AND BATTERY PACK:

■ Red LED on = Fast charging mode.

■ Green LED on = Fully charged battery pack.

■ No LED on = Defective charge or battery pack.

CHARGING YOUR BATTERY PACK

The battery pack for your tool has been shipped in a low

charge condition to prevent possible problems.

Therefore, you should charge it prior to use.

Note: Batteries will not reach full charge the first time

they are charged. Allow several cycles for them to

fully charge.

TO CHARGE

■ Charge battery pack only with the charger provided.

■ Make sure power supply is normal house voltage,

230 volts, 50 Hz, AC only.

■ Connect charger to power supply.

■ Place battery pack in charger. Align raised rib on

battery pack with groove in charger.

■ Press down on battery pack to be sure contacts on

battery pack engage properly with contacts in charger.

When properly connected, red light will turn on.

■ When your battery pack becomes fully charged, the

red light will turn off and the green light will turn on.

■ After normal usage, 1 hour of charge time is required

to be fully charged. A minimum charge time of 1 to

1-1/2 hours is required to recharge a completely

discharged tool.

■ DO NOT place charger in an area of extreme heat or

cold. It will work best at temperatures above 10°C

and below 38°C.

960001208-02 12/23/03 11:41 AM Page 9

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi cmd 1202 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ryobi cmd 1202 Manual

Product: