383094
19
Zoom out
Zoom in
Previous page
1/209
Next page
SPECIFICATION
ALTERNATIVE METHOD FOR RIP CUTTING
44. STRAIGHTEDGE
45. C-CLAMPS
46. WORKPIECE
47. RIPFENCE SCREW (WING SCREW)
48. RIPFENCE (EDGE GUIDE)
49. PLACE RIPFENCE THROUGH HOLES
KNOW YOUR CORDLESS CIRCULAR SAW
Before attempting to use a tool, familiarize yourself with all
its operating features and specific safety requirements.
Features include easily operated bevel cut and depth of
cut adjustment mechanisms, positive 0° bevel stop,
spindle lock and blade key storage compartment.
See Figure 1.
Applications
Only use your saw for the purpose listed below:
Cutting all types of wood products (lumber, plywood,
paneling).
Trigger Switch
Your saw is equipped with a lock-off button which
reduces the possibility of accidental starting. The lock-off
button is located on the handle above the trigger switch.
You must depress the lock-off button in order to pull
the switch trigger. The lock resets each time the trigger
is released.
Note: You can depress the lock-off button from either the
left or right side.
WARNING
Always wear safety goggles or safety glasses
with side shields when operating tools. Failure to
do so could result in objects being thrown into
your eyes, and cause serious eye injury.
WARNING
Do not allow familiarity with your cordless circular
saw to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
severe injury.
WARNING
A150 mm (6") blade is the maximum blade
capacity of your saw. Never use a blade that is
too thick to allow outer blade clamp to engage
with the flats on the spindle. Larger blades will
come in contact with the blade guard, while
thicker blades will prevent blade screw from
securing blade on spindle. Either of these
situations could result in a serious accident.
TO ASSEMBLE OR REMOVE BLADE
TO ASSEMBLE BLADE
Remove battery pack from saw.
WARNING
Failure to remove battery pack from the saw
could result in accidental starting and cause
serious personal injury
Depress latch on end of battery pack and release it
from your saw. See Figure 2.
Remove blade key (5 mm hex key) from its storage
compartment. See Figure 1.
Depress spindle lock button and remove blade screw
and outer blade washer. See Figure 3.
Note: Turn blade screw clockwise to remove it.
Put a drop of oil onto inner blade washer and outer
blade washer where they touch the blade.
WARNING
If the inner blade washer has been removed,
put it back in place before placing the blade on
the spindle. Failure to do so could cause an
accident since the blade will not tighten properly.
Fit saw blade inside blade guard and onto spindle.
Note: The saw teeth point upwards at the front of saw
as shown in Figure 3.
Put outer blade washer back in place.
Depress spindle lock button, then replace blade
screw. Tighten blade screw securely.
Note: Turn blade screw anticlockwise to tighten.
Return blade key to storage compartment.
REMEMBER: Never use a blade that is too thick to
allow the outer blade washer to engage with the flat
on the spindle.
15
GB
English
F D E I P NL S DK N FIN GR H CZ RUS PL
RO
SLO TR
HR
CCS-1801DM 1/06/05 14:53 Page 15
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ryobi ccs 1801dm one at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ryobi ccs 1801dm one in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info