PACKAGE HANDLING INSTRUCTIONS
-The machine is supplied in a corrugated cardboard box with overall di-
mensions 35x35xh60 cm weighting 8 Kg.
- The box must be handled and stored in the upright position.
- Do not place any objects on the package that have a different sized ba-
se than the package.
Unpacking instructions
-Carefully inspect the box before opening; if it is damaged or seems to
have been previously opened, do not open. Reject the box and register
a complaint with the carrier. Failure to do so will void the warranty.
-To unpack the machine, open the corrugated cardboard box, remove the ma-
chineand set aside the bag of accessories.
To dispose of packaging materials, observe the regulations in effect
where the machine is installed, in consideration of recycling rules
when applicable.
Inspection of package contents
The package contains:
- the machine equipped with power cord;
-1 vacuum fixture (19) complete with 5 mm terminals for electric tools
with accessories;
- n° 1 spare dust bag (8);
- a vacuum fixture (20) is available upon request complete with terminals
and air fittings m 5 for pneumatic tools;
- a hose fixture is available upon request.
WARNINGS
Safety and accident prevention instructions
The machine must only be used by trained and qualified personnel.
The machine must be located in a dry and well-ventilated area where air
is changed at least once an hour with 50% of the total fresh air without
the aid of special ventilation systems. The temperature of the work area
must be between 10°C and 35°C with humidity between 50% and 90%.
Always unplug the machine when not in use, before maintenance or clea-
ning and before replacing the dust bag or filter. Do not pull the power cord
to unplug the machine.
Keep the power cord away from heat, oil and sharp corners.
In the event of a blackout, turn the switch of the connected tool to the OFF po-
sition to avoid it from accidentally starting when power returns. Do not ex-
pose the machine to rain.
Explosion or fire hazard
-Do not vacuum flammable or explosive dust (i.e. magnesium, alumi-
nium, asbestos, etc.);
-do not vacuum flammable or explosive liquids (i.e. petrol, thinners,
etc.);
-do not vacuum aggressive liquids or substances (i.e. acids , bases, sol-
vents, etc.);
- do not vacuum sanding dust from surfaces treated with paints that ha
-
ve not completed the catalyst cycle
;
- immediately disconnect the vacuum from the electrical mains if dust is
discharged;
- use the fire alarm system and leave the area in the event of fire.
Specific use
The machine is high stress qualified for industrial applications according
to regulations EN60335-1 and EN60335-2-69.
The machine is designed to vacuum dry sanding dust with all exposure
limit values due to the work type. The machine supplies, simultaneously
and near the work area:
-the possibility of accessing energy sources to power electrical and
pneumatic tools without the use of extension cords;
- the availability of a sanding dust vacuuming system.
TECHNICAL SPECIFICATIONS
OPERATING VOLTAGE
ABSORBED POWER
ABSORBED CURRENT
MAX TOOL POWER
MAX TOTAL POWER
MAX TOTAL ABSORBED CURRENT
VACUUM CAPACITY
DEPRESSION
WEIGHT
DIMENSIONS
NOISE LEVEL
FILTER SURFACES
FILTER CATEGORY
BAG CAPACITY
ELECTRICAL SOCKETS
3-WAY SWITCH
220/240 Vac - 50/60 Hz
1100 W
4 A
1 x 2500 W max
3600 W max
15,7 A
180 m
3
/h
1700 mm/H
2
O
6 Kg
cm 32 x 32 x h 56
75 dB (A)
m
2
0,20
M
Kg 7 max
1
MAN - OFF - AUT
PNEUMATIC SECTION (only EP versions)
INPUT AIR PRESSURE
MAX AIR CAPACITY
POWER FIXTURE
PNEUMATIC FITTINGS
6 bar max
1500 l/min
3/8” G female
1
PARTS OF THE TOOL
1 - vacuum head
2 - 3-way switch (MAN-OFF-AUT)
3 - identification plate
4 - transport handle
5 - head clips
6 - power cord
7 - electric tool socket
8 - dust bag
9 - bag outlet
9a - bag outlet cap
10 - filter
11 - filter for liquids
12 - pneumatic power inlet (only EP versions)
13 - pneumatic tool coupling (only EP versions)
14 - suction pipe-union inlet
15 - suction pipe-union
16 - wheels
17 - pneumatic tool fixture
18 - vacuum fixture
19 - electric tool sleeve
20 - pneumatic tool sleeve (optional)
21 - basket and float
22 - vacuum drum
START-UP
Minimum power supply requisites and connections:
Electric mains - Single-phase voltage 230V 50/60Hz with grounding wire
mm
2
3x1.5.
Compressed air mains - Working pressure not over 6 bar; the main-
smust supply dehumidified and filtered air. Having assembled arubber
hose fixture (optional), connect the machine to the pneumatic mains with
a hose, whose length supports working pressure, of 10mm minimum
internal Ø.
After having checked that the switch (2) is in the "O" position, insert the
power cord plug in a socket that supports the machine load.
Wheel (16) and pipe-union (15) assembly
- Open the lock hooks (5) and lift the vacuum head (1);
- pull out the wheels and the accessories;
- turn the drum upside down (22) and press the wheels (16) into the re-
levant slots;
- insert the pipe-union (15) into the inlet (14) (fig. 1).
ENGLISH
Read the following instruction first before operate the product.
PICTOGRAPH
Important safety indications.
6
