489889

Rupes NL16 Manual

10
Zoom out
Zoom in
Previous page
1/34
Next page
10
ELECRONIC RPM CONTROL (NL13EMCR)
The maximun rpm can be adjusted by rotating the control (6) lo-
cated on the swich. Progressive control is obtained by gradually
increasing the pressure on the swicth.
REPLACING DRILL BITS
- Open the chuck jaws by rotating the mobile ring (12) while kee-
ping the fixed ring (13) still.
- Replace the drill bit and tighten as described in the “FITTING
DRILL BITS” chapter.
MIXER PADDLE REPLACEMENT
- Hold the mixer chuck with the steady ring (13) and release the swiv-
elling ring (12) to expand the jaws;
- replace and lock the mixer paddle as shown in
“MIXER ASSEMBLY”.
USABLE WORKING TOOL
Drill bits avaiable on the market (NL13 - NL16)
Standard hexagonnal attachment mixer paddle Ø max 120 mm
(NL13EMCR - NL16Tool)
MAINTENANCE (aliminata la seconda riga)
All maintenance operations are carried out with the power supply
disconnected.
At the end of each work session, or when required, remove any
dust from the body of the tool using a jet of compressed air,
paying particular attention to the motor ventilation slots.
No other maintenance operations must be undertaken by the
user.
Maintenance and cleaning of the inner parts, like brushes, ball
bearings, gears etc. or others, must be carried out only by an au-
torised customer-service workshop.
ELECTRIC SAFETY - LOW TENSION
The tests have been carried out in accordance with the standard:
EN 60745-1 safety of hand-held electric motor operated tools
EN 60745-2-1 specific drill rules
RADIO SUPPRESSION
The tools are suppressed in accordance for the prevention and
elimination of radio disturbances measured in accordance with
standard: EN55014-1+EN55014-2; EN61000-3-2+EN61000-3-3.
NOISE
The noise level produced is 77 dB, measured according to
regulation EN ISO 3744 + UNI EN ISO 11203.
Warning: wear suitable hearing protections! (see warnings).
MEAN ACCELERATION VALUE
The mean quadratic acceleration value is less than 2,5 m/sec
2
measured in accordance with standard UNI EN 28662 + UNI EN
ISO 5349.
GUARANTEE
All tools manufactured by RUPES Spa are guaranteed for 12
months from the date of purchase against fabrication and mate-
rial defects.
All tools must be used only with RUPES original accessories and
spare parts: we refuse all responsibility for damages or accidents
caused by non-observance of this rule which will also cause the
termination of the guarantee.
The guarantee will no longer be valid if the instructions contained
in this booklet are not followed, if the tool is used for purposes
other than that for which it is intended, if it is dismantled, interfe-
red with in any way or damaged due to neglect.
The guarantee will be made valid by filling-in the form on the
inside back cover of this instruction booklet.
If the tool is found to be defective or malfunctions, it should be re-
turned carriage free in one piece in its original packing together
with the guarantee certificate to the manufacturer or to one of the
Assistance Centres listed in the appendix to this booklet.
The guarantee does not automatically imply replacement of the
tool.
RUPES Spa reserves the right to make any technical or design
modification to its products without prior notice.
The manufacturer is not liable for any print errors. This document
voids and replaces previous ones.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rupes NL16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rupes NL16 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info