489889

Rupes NL16 Manual

9
Zoom out
Zoom in
Previous page
1/34
Next page
9
PARTS OF THE TOOL
1 - Identification plate
2 - ON-OFF switch
3 - Switch locking button
4 - Tool body
5 - Rear handle
6 - Gearbox
7 - Side-handle housing
8 - Additinal handle
9 - Chuck
10 - Mobile ring (NL 13 - NL 16)
11 - Fixed ring (NL 13 - NL 16)
12 - Motor ventilation slotts
STARTING UP
Before starting-up the tool, ensure that:
- the packaging is complete and does not show signs of having been
damaged during storage or transport;
-the tool is complete; check that the number and type of
components comply with that reported in this instruction booklet;
- the power supply and socket outlet can support the load reported in
the table and that indicated on the tool identification plate
reproduced and explained on page 11.
ASSEMBLING THE TOOL
ASSEMBLING THE SIDE HANDLE
Screw the handle (8) into the threaded hole on the gearbox. The
handle can be positioned on the right or left of the tool.
FITTING DRILL BITS
1. Keep the chuck still using the fixed ring and unscrew the mobile
ring until the jaws are sufficiently open to hold the drill bit.
2. Lock the drill bit by rotating the upper part of the chuck in a
clockwise direction.
3. Check that the bit does not rotate off-centre.
MIXERS ASSEMBLY
1. Hold the mixer chuck with the stready ring and release the swivel-
ling ring to expand the jaws;
2. lock the mixer paddle turning clocwise the chuck swivelling ring;
3. check the mixer paddle balancing.
BEFORE STARTING THE TOOL
Ensure that:
- the power supply conforms with the characteristics of the tool;
- the power supply cable and plug are in perfect condition;
- the ON/OFF switch works properly though with the power supply di-
sconnected;
- all the parts of the tool have been assembled in the proper manner
and that there are no signs of damage;
- the ventilation slots are not obstructed (7);
- the dust bag is enipty and not torn.
STARTING AND STOPPING
- Starting:
push the switch level (2) so that it enters the housing in the
rear handle. To lock the switch in the on position, press the lock but-
ton (3) at the same time.
- Stopping:
release the switch. If locked in poition, keep pressing un-
til the look is released.
TEST RUN
Start the machine and check the drill-bit or mixing-paddle alignment.
Otherwise, switch-off the tool immediately and eliminate the cause.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rupes NL16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rupes NL16 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info