489883
11
Zoom out
Zoom in
Previous page
1/53
Next page
BEFORE FREEING JAMMED MATERIAL
- Turn tool “OFF” by releasing trigger switch,
- Wait for all moving parts to stop,
- Unplug the machine.
BEFORE LEAVING THE MACHINE NEVER
LEAVE TOOL RUNNING UNATTENDED
- Turn power off,
- Wait for all moving parts to stop,
- Unplug.
W
ARNING: The operation of any power tool
can result in foreign objects being thrown into
your eyes, which can result in severe eye dama-
ge. Before beginning tool operation, always wear
safety goggles of safety glasses with side shields
and a full face shield when needed. We recom-
mend Wide Vision Safety Mask for use over eye-
glasses or standard safety glasses with side
shields.
MAKE WORKSHOP CHILD PROOF
- Lock the shop,
- Disconnect master switches,
- Store tool away from children and others not
qualified to use the tool.
Look for this symbol to point out important
safety precautions. It means attention!!! Your
safety is involved.
MOTOR AND ELECTRICALREQUIREMENTS
WARNING: To reduce the risk of electrical
hazards, fire hazards or damage to the tool, use
proper circuit protection. Your machine is wired at
the factory for operation using the voltage shown
above. Connect tool to a power line with the
appropriate voltage and a 16-amp branch circuit.
Use a 16-amp time delay type fuse or circuit
breaker. To reduce the risk of shock or fire, if
power cord is worn or cut, or damaged in any
way, have it replaced immediately.
ELECTRICAL CONNECTIONS
NOTE: The plug supplied on your tool may not fit
into the outlet you are planning to use. Your local
electrical code may require slightly different
power cord plug connections. If these differences
exist refer to and make the proper adjustments
per your local code before your tool is plugged in
and turned on. In the event of a malfunction or
breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of
electric shock. This tool is equipped with an elec-
tric cord having an equipment grounding conduc
-
tor and a grounding plug, as shown. The plug
must be plugged into a matching outlet that is
properly installed and grounded in accordance
with all local codes and ordinances. Do not modi-
fy the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified
electrician.
Improper connection of the equipment grounding
conductor can result in a risk of electric shock.
The conductor with insulation having an outer
surface that is green with or without yellow stri-
pes is the equipment grounding conductor. If
repair or replacement of the electric cord or plug
is necessary, do not connect the equipment
grounding conductor to a live terminal.
If power cord is worn or cut, or damaged in any
way, have it replaced immediately by a qualified
electrician. If the grounding instructions are not
completely understood, or if you are in doubt as
to whether the tool is properly grounded check
with a qualified electrician or service personnel.
W
ARNING: Do not permit fingers to touch the
terminals of plug when installing or removing the
plug from the outlet to avoid injury or possible
death from electrical shock.
W
ARNING
: If not properly grounded, this tool
can cause an electrical shock, particularly when
used in damp locations, in proximity to plumbing,
or out of doors. If an electrical shock occurs there
is the potential of a secondary hazard, such as
your hands contacting the mixing paddle.
MOTOR SAFETYPROTECTION
IMPORTANT: To avoid motor damage, this
motor should be blown out or vacuumed frequen-
tly to keep dust from interfering with normal motor
ventilation.
1. Connect this tool to a power source with the
appropriate voltage for your model and a 16-amp
branch circuit with a 16-amp time delay fuse or
circuit breaker. Using the wrong size fuse can
damage the motor.
2. If the motor won’t start, turn the switch off
immediately and unplug the tool.
3. If the motor suddenly stalls while mixing, relea-
se the trigger switch, unplug the tool.
The motor
may now be restarted.
4. Fuses may "blow" or circuit breakers may trip
frequently for the following reasons:
a.
Motor Is Overloaded-Overloading can occur
if you feed too rapidly or make too many
start/stops in a short time.
b. Line voltages should not be more than 10%
11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rupes MX800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rupes MX800 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info