6
empty.
Remove the water tank (fig.2) and fill it up
(fig.16). Replace it fully into its housing (fig.4)
until there is a click.
Press the Restart button and the red indicator
light goes out; you can continue ironing.
8 • Dry ironing
Do not press the steam control button beneath
the iron handle. Do not press the “Precision
Steam Jet” button or humid steam button on the
iron handle
9 • Using damp steam
Press 2 or 3 times on the humid steam button to
obtain a more powerful, heavier burst of steam :
- for ironing thicker fabrics,
- to eliminate creases.
10 • Using the burst of
freshness function *
The burst of freshness function allows you to give
long-lasting freshness to your laundry.
Burst of freshness function : Move the selection
slide downwards (fig.17). Press the burst of
freshness button (fig.18) on the top of the iron
handle 2 or 3 times to obtain an intermittent jet of
freshness steam at the front of the iron.
11 • Replacing the capsule
Remove the capsule housing drawer by pulling it
out horizontally.
Remove the used capsule. Pull the red tab to
remove the seals on the refill capsule (fig.6).
Insert the capsule in its housing, pressing down
firmly until there is a “click” (
fig.7).
Close the drawer again by pushing it in
horizontally until there is a closing “click” (fig.8).
12 • Use the precision steam
jet function
The “Precision Steam Jet” function, allowing you
to iron the most hard-to-reach areas (such as
button holes, shirt cuffs and collars, darts in
trousers, the inside of jacket and coat sleeves) ;
soften the fibres before ironing, when the fabric is
very creased.
Precision steam jet function : Move the selection
slide Fresh off upwards (fig.19). Press the
“Precision Steam Jet” button (fig.20) on the top
of the iron handle 2 or 3 times to obtain short,
powerful bursts of steam at the front of the iron.
Then iron the fabric using steam to smooth the
fibres, by pressing the steam control button
beneath the iron handle.
USE IN CREASE REMOVAL
MODE
13 • Vertical steam ironing
The crease-removal brush makes it possible to
remove creases from certain materials that do not
crease much (viscose, polyester, etc.); to refresh
clothes that have already been worn; to add
finishing touches (removal of marks from
handling on the ironing board) and to eliminate
certain unpleasant odours.
Put the Ironing / Crease Removal selector to the
Crease Removal position (fig.21). The brush’s
indicator light switches on.
When using the brush for the first time, press the
steam control until steam appears.
Hang the garment on a hanger.
Pull the brush flex fully out of its housing (fig.22).
Set the steam flow button to the max position.
Wait until the green indicator light (located on the
control panel) remains steady.
If you have not used the brush for a few minutes,
press the steam function several times in a row,
away from your clothes.This will enable any cold
water to be removed from the steam circuit.
Hold the fabric with one hand, put the brush in
contact with the fabric to be treated and press the
steam control on the brush intermittently, moving
CAUTION! In the intermediate position, the
green indicator light flashes rapidly : neither
the iron nor the brush functions.
Refill capsules are commercially available
under the reference: XD7000F0.
BE CAREFUL ! Use the humid steam function
very carefully because of the exceptional
power of steam that may cause burns.
IMPORTANT! Remove the needle and the
red cover from the capsule before inserting
it into the iron.
On first use, the fragrance may take a
moment to come through (approximately 10
seconds).
The fragrance capsule allows you to treat up
to 200 items of laundry at a rate of spraying
1 or 2 seconds per item.
Tip: for increased effectiveness, use the
fragrance at the end of ironing clothing or
household linen.
* depending on model
