656106
33
Zoom out
Zoom in
Previous page
1/52
Next page
32
ROTWILD USER MANUAL | 2014
GETTING READY
ROTWILD bikes come almost completely
assembled ready-to-ride bikes or as a frameset.
ROTWILD mountain bikes may only be used in
off-road situations and not in general public traf-
fic. Please observe your local traffic regulations.
Before your first ride with so called „click
pedals“ you have to familiarise yourself with
the clip-in and clip-out action. Always read the
instruction manual first.
Pedals
To mount your pedals, you will need an
appropriate open-end wrench or allen key.
Before you screw the pedals into the crank
arm, apply a little assembly grease to the
threads and make sure that you insert the
washers between the pedal and the crank if
supplied.
When screwing the pedals into the crank,
please note that the right pedal side has a
right-handed thread (tighten in a clockwise
direction) while the left side has a left-handed
thread (tighten in an anti-clockwise direction).
Handlebars and stem positioning.
With the help of the stem-handlebars device
it is possible to adjust the ROTWILD bike to
the desired seating position. In addition to the
height of the handlebars it is possible to positi-
on the handlebars inclination.
Home position
Slightly release the screws to be found on the
stem with the help of a fitting allen key/torx
wrench, so the handlebar can turn.
Swing the handlebars forwards out of the
transport position into the home position. The
centring mark to be found on the handlebars
should be positioned exactly between the two
stem clamps.
Slightly pull the stem clamps in order to
secure the handlebars position.
Now open the rear two stem clamp screws
with the help of a fitting allen key/torx wrench
in order to position the handlebars stem
device. Align the handlebars at a right angle to
the front wheel.
Gradually tighten both the stem clamp
screws alternately – clamping torque 8 Nm.
Control: Put the front wheel between your
legs. The fixation is correct when you can no
longer twist the handlebar.
Now align the handlebars (incline).
The Road Bike handlebars should be positioned
in a way that the lower handle bar is parallel to
the road in the home position.
It is recommended to tighten the stem clamp
screws one after the other or crossed by
hand, in order to achieve a possible even
division of the screw strength. After the
handlebars have been secured use the torque
spanner – clamping torque 6 Nm.
Control: Grip the brake handle from above.
The fixation is correct when you can no
longer twist the handlebars up or down.
GETTING READY
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rotwild 2014 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rotwild 2014 in the language / languages: English, German as an attachment in your email.

The manual is 1,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info