714277
22
Zoom out
Zoom in
Previous page
1/24
Next page
22
Lock the cutting
insert holder by
slightly turning it into
direction ‘CLOSE’.
Put the feed chute
into the corresponding
slots on the base unit.
(This can be done in 3
positions).
Lock the feed
chute by turning
it to the right into
direction „locked
lock“, until it audibly
engages.
Insert the pusher into
the feed chute.
Put the collecting
container on the base
unit. Pay attention
that the safety switch
is correctly positioned
above the container.
3.) How to start / stop the appliance
IMPORTANT: Before fitting the base unit to the collecting container, please check whether the appliance
has been switched on unintentionally!
To do so, remove the base unit from the collecting container.
Then plug the mains plug into a power socket.
If the operation pilot lamp lights up, the appliance is switched on. In this case switch off the appliance by
pressing the ON/OFF switch. The operation pilot lamp turns off.
After you are sure that the appliance is switched off, you can put the base unit on the collecting container.
NOTE: The appliance is designed for short-term operation only resp. for a maximum continuous operation
time of 2 minutes. After this time limit is reached, allow the appliance to cool down for at least 2 minutes.
If this is not respected, the motor may be damaged!
To start, press the ON/OFF switch. The appliance starts and the pilot lamp lights up continuously.
To stop, press the ON/OFF switch once again. The appliance stops and the pilot lamp turns off.
4.) How to start processing food
Put the food to be cut in the centre of the pusher and press firmly. This is important in order to be able
to apply an even pressure on the food.
Insert the pusher with the attached food into the feed chute.
Start the appliance by pressing the ON/OFF switch.
Only apply a gentle and even pressure to the pusher to push the food downwards.
Always firmly hold the pusher during the slicing process.
Switch the appliance off during reloading the pusher.
Empty the collecting container from time to time.
5.) Food separates from the pusher
Should a piece of food separate from the pusher during operation, stop the appliance by pressing the
ON/OFF switch.
Disconnect the mains plug from the socket before removing residues from the cutting insert.
Remove residues from the cutting insert and put the food on the pusher once again.
Then restart the processing.
6.) How to switch off the appliance completely
Pull the power plug after each use for safe switch-off!
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rommelsbacher EGS80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rommelsbacher EGS80 in the language / languages: English, German as an attachment in your email.

The manual is 3,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info