757755

Roland Zenology Manual

6
Zoom out
Zoom in
Previous page
1/111
Next page
to Contents
2 StructureStructure
Structure lets you sound two partials as a set.
You can create a wide range of sounds by using partial 2 or 4 (the modulator) to modulate
partial 1 or 3 (the carrier).
Since the Structure uses two partials as a pair, it provides parameters that are used in
common by the carrier and modulator.
[PITCH] [OSC] [LFO] [FILTER] [AMP/EQ]
buttons
Shows the module selected in the tone VISUAL/PRO screen
for all four partials (module layout).
[RANGE/CTRL] button
Shows a layout in which the tone VISUAL/PRO screen
shows the velocity range and matrix control edit screen
of each partial.
[L] button
Turns the partial on/o.
[PARTIAL 1–4] button
Shows all modules of the selected partial in the tone
VISUAL/PRO screen (partial layout).
[OFF] button
The two partials are used individually (not as a pair).
[SYNC] button
Implements the oscillator sync function that is provided by
an analog synthesizer.
The partial 1 oscillator is reset at intervals of partial 2’s
pitch cycle.
* This is eective only if OSC Type is VA or PCM-Sync.
[RING] button
Implements the ring modulator function that is provided
by an analog synthesizer.
The output sound of partial 2 is multiplied with partial 1.
[XMOD] [XMOD2] buttons
XMOD
XMOD2
Implements the cross modulation function that is provided
by an analog synthesizer.
The output sound of partial 2 is applied as the pitch of
partial 1.
* XMOD2 is available only when Partial 1 and 3 are OSC Type
“ VA .”
PRO EDIT parameter (STRUCTURE)
Structure lets you sound two partials as a set.
You can create a wide range of sounds by using partial 2 or 4 (the modulator) to modulate partial 1 or 3 (the carrier).
Since the Structure uses two partials as a pair, it provides parameters that are used in common by the carrier and
modulator.
For the following parameters, only the partial settings of the carrier are valid (the settings of the modulator are ignored).
KEYBOARD
5Keyboard Range Lower
5Keyboard Range Upper
5Keyboard Fade Width Lower
5Keyboard Fade Width Upper
5Velocity Range Lower
5Velocity Range Upper
5Velocity Fade Width Lower
5Velocity Fade Width Upper
SWITCH
5Partial Switch
OSC
5Delay Mode (note)
5Delay Mode
5Delay Time Sync
5Delay Time (note)
5Delay Time
CONTROL
5Envelope Mode
5Receive Hold-1
5Redamper Switch
5Damper Free Note
5MATRIX CONTROL
5Destination: PMT
5Destination: CROSS-MOD
Structure1-2
The sound of partial 1 is modulated by partial 2.
OFF OFF
SYNC
Implements the oscillator sync
function that is provided by an analog
synthesizer.
The partial 1 oscillator is reset at
intervals of partial 2’s pitch cycle. This is
eective only if OSC Type is VA or PCM-
Sync.
RING
Implements the ring modulator
function that is provided by an analog
synthesizer.
The output sound of partial 2 is
multiplied with partial 1.
XMOD,
XMOD2
Implements the cross modulation
function that is provided by an analog
synthesizer.
The output sound of partial 2 is applied
as the pitch of partial 1.
XMOD2 is available only when Partial 1
and 3 are OSC Type “VA.”
Structure3-4
The sound of partial 3 is modulated by partial 4.
OFF OFF
SYNC
Implements the oscillator sync
function that is provided by an analog
synthesizer.
The partial 3 oscillator is reset at
intervals of partial 4’s pitch cycle. This is
eective only if OSC Type is VA or PCM-
Sync.
RING
Implements the ring modulator
function that is provided by an analog
synthesizer.
The output sound of partial 4 is
multiplied with partial 3.
XMOD,
XMOD2
Implements the cross modulation
function that is provided by an analog
synthesizer.
The output sound of partial 4 is applied
as the pitch of partial 3.
XMOD2 is available only when Partial 1
and 3 are OSC Type “VA.”
RING1-2 Level
0–127 RING level when Structure1-2 is RING.
RING3-4 Level
0–127 RING level when Structure3-4 is RING.
RING OSC1 Level
0–127 Eective when Structure1-2 is RING.
Sets the partial 1 OSC level.
RING OSC2 Level
0–127 Eective when Structure1-2 is RING.
Sets the partial 2 OSC level.
RING OSC3 Level
0–127 Eective when Structure3-4 is RING.
Sets the partial 3 OSC level.
RING OSC4 Level
0–127 Eective when Structure3-4 is RING.
Sets the partial 4 OSC level.
XMOD 1-2 Depth
0–9600 [cent] Cross Modulation Depth when
Structure1-2 is XMOD.
XMOD 3-4 Depth
0–9600 [cent] Cross Modulation Depth when
Structure3-4 is XMOD.
XMOD2 1-2 Depth
0–127 Cross Modulation Depth when
Structure1-2 is XMOD2.
XMOD2 3-4 Depth
0–127 Cross Modulation Depth when
Structure3-4 is XMOD2.
CrossMod OSC1 Level
0–127 Eective when Structure1-2 is XMOD/
XMOD2. Sets the partial 1 OSC level.
CrossMod OSC2 Level
0–127 Eective when Structure1-2 is XMOD/
XMOD2. Sets the partial 2 OSC level.
CrossMod OSC3 Level
0–127 Eective when Structure3-4 is XMOD/
XMOD2. Sets the partial 3 OSC level.
CrossMod OSC4 Level
0–127 Eective when Structure3-4 is XMOD/
XMOD2. Sets the partial 4 OSC level.
Partial Phase Lock
OFF, ON
This is available if OSC Type is “VA”; it
locks the waveform phase between
partials. It is eective to use this with
XMOD2.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland Zenology at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland Zenology in the language / languages: English as an attachment in your email.

The manual is 29,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info