537618
221
Zoom out
Zoom in
Previous page
1/252
Next page
221
MIDI Implementatie
System Exclusive Message
MIDI Machine Control (MMC)
* Received when the MMC Mode parameter (SYSTEM/MIDI/MMC MTC) is SLAVE.
STOP (MCS)
Status Data byte Status
F0H 7FH, dev, 06H, 01H F7H
Byte Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC command message
01H STOP (MCS)
F7H EOX (End of Exclusive)
DEFERRED PLAY (MCS)
Status Data byte Status
F0H 7FH, dev, 06H, 03H F7H
Byte Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC command message
03H DEFERRED PLAY (MCS)
F7H EOX (End of Exclusive)
LOCATE (MCP)
Format2-LOCATE [TARGET]
Status Data byte Status
F0H 7FH, dev, 06H, 44H, 06H, 01H, F7H
hrH, mnH, scH, frH, ffH
Byte Remarks
F0H Exclusive status
7FH Universal System Exclusive Realtime Header
7FH Device ID
06H MMC command message
44H LOCATE (MCP)
06H Byte count
01H ‘TARGET’ sub-Command
hrH Standard Time Specification with subframes
mnH
scH
frH
ffH
F7H EOX (End of Exclusive)
4. Data Transmission (Sequencer Section)
4.1 Messages transmitted during playing
Recorded messages are transmitted during playback.
4.2 Soft Thru setting
Messages (except System Common and System Realtime Messages) that are received are
then sent out when Soft Thru parameter (SYSTEM/MIDI) is switched to ON.
4.3 Messages that are generated and transmitted
4.3.1 Messages Appearing When Synchronizing
with Other Devices
System Common Messages
* Sent when Sync Output parameter (SYSTEM/TEMPO/SYNC) is set to ON.
Song Position Pointer
Status 2nd byte 3rd byte
F2H mmH llH
mm, ll=value: 00 00H - 7F 7FH (0 - 16383)
System Realtime Messages
* Sent when Sync Output parameter (SYSTEM/TEMPO/SYNC) is set to ON.
Timing Clock
Status
F8H
Start
Status
FAH
Continue
Status
FBH
Stop
Status
FCH
Quarter Frame Messages
Status 2nd byte
F1H mmH (= 0nnndddd)
* Sent when Sync Mode parameter (SYSTEM/TEMPO/SYNC) is set to MASTER and
MTC Sync Output parameter (SYSTEM/MIDI/MMC MTC) is set to ON. Furthermore,
sending a Quarter Frame Message with ‘00h00m00s00f00’ at the beginning of the song
adds the MTC Offset Time parameter (SYSTEM/MIDI/MMC MTC).
221


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland Juno-G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland Juno-G in the language / languages: Dutch as an attachment in your email.

The manual is 8,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info