Manual Roland Juno Di (page 76 of 136) (English)

499471

Zoom out

Zoom in

1/136

Other Settings

HOLD

PEDAL

Assign

VIB-RATE,

VIB-DEPTH,

VIB-DELAY,

CHORUS-SEND,

REVERB-SEND,

AFTERTOUCH,

START/STOP,

TAP-TEMPO,

PROG-UP,

PROG-DOWN,

FAV-UP,

FAV-DOWN

VIB-RATE (CC76):

Vibrato speed

VIB-DEPTH (CC77):

Vibrato depth

VIB-DELAY (CC78):

Vibrato delay time

CHORUS-SEND (CC93):

The amount of the chorus

REVERB-SEND (CC91):

The amount of the reverb

AFTERTOUCH:

Channel aftertouch

START/STOP:

Pressing the pedal will start/stop the Song Player (p. 72) or Rhythm Pattern (p. 74).

TAP-TEMPO:

The tempo will be set to the interval at which you press the pedal (Tap Tempo).

PROG-UP:

If you’re playing a single sound, this selects the next sound. If you’re playing multiple sounds (i.e., when the

[PERFORM] button is lit), this selects the next-numbered performance.

PROG-DOWN:

If you’re playing a single sound, this selects the previous sound. If you’re playing multiple sounds (i.e.,

when the [PERFORM] button is lit), this selects the previous-numbered performance.

FAV-UP:

The favorite of the next number or bank will be selected.

FAV-DOWN:

The favorite of the previous number or bank will be selected.

Continuous

Hold

OFF, ON

If “Assign” is set to “HOLD,” turning this “ON” allows the HOLD PEDAL jack to support half-pedaling.

When this is set to support use of half-pedaling techniques, you can then connect an optional expression pedal (DP-10,

etc.), and employ pedal work to achieve even finer control in performances in which piano tones are used.

Polarity

STANDARD,

REVERSE

Selects the polarity of the pedal connected to the HOLD PEDAL jack.

On some pedals, the electrical signal output by the pedal when it is pressed or released is the opposite of other pedals. If

your pedal has an effect opposite of what you expect, set this parameter to “REVERSE.” If you are using a Roland pedal (that

has no polarity switch), set this parameter to “STANDARD.”

MIDI

Local Switch

OFF, ON

Determines whether the internal sound generator is disconnected (OFF) from the controller section (keyboard, pitch

bend/modulation lever, knobs, buttons, D Beam controller, pedal, and so on); or not disconnected (ON).

Normally this is left “ON,” but if you wish to use the JUNO-Di’s keyboard and controllers to control only external sound

modules, set it to “OFF.”

Patch Rx/Tx Ch

1–16

Channel used to transmit and receive MIDI messages for the keyboard part. For details, refer to “Setting the Receive

Channel” (p. 82).

Tx Edit Data

OFF, ON

Specifies whether changes you make in the settings of a tone, performance will be transmitted as system exclusive

messages (ON), or will not be transmitted (OFF).

Soft Through

OFF, ON

If this is “ON,” incoming MIDI messages from the MIDI IN connector will be re-transmitted without change from the MIDI

OUT connector.

Sync Mode

MASTER, SLAVE

Specifies the synchronization message that the JUNO-Di will use for operation.

MASTER:

The JUNO-Di will be the master. Choose this setting when using the JUNO-Di by itself without synchronizing

to another device.

SLAVE:

The JUNO-Di will be the slave. Choose this setting when you want the JUNO-Di to synchronize to MIDI Clock

messages received from another MIDI device.

USB Driver

VENDER,

GENERIC

Sets the USB driver.

* This setting will take effect when you turn the power off, then on again.

MIC IN

SETTINGS

Rev Level

(Reverb Level)

0–127

Adjust the amount of reverb that is applied to the sound of the microphone.

Rev Type

(Reverb Type)

ROOM1, ROOM2,

STAGE1,

STAGE2,

HALL1, HALL2,

DELAY,

PAN-DELAY

Select the type of reverb/delay

ROOM1:

Short, high-density reflections

ROOM2:

Short, low-density reflections

STAGE1:

Greater amount of late reverberation

STAGE2:

Stronger early reflections

HALL1:

Clear-sounding reverberation

HALL2:

Rich-sounding reverberation

DELAY:

Conventional delay

PAN-DELAY:

Delay that moves the reflections between left and right

Rev Time

(Reverb Time)

0–127

Adjusts the length of the reverberation (when Rev Type is ROOM1–HALL2) or the delay time of the delay (when Rev Type

is DELAY or PAN-DELAY).

Mic Mode

ALL, VOCODER

Specifies whether the sound from the mic will be output at all times (ALL) or only if MFX (p. 61) is set to “79:VOCODER”

(VOCODER).

MINUS

ONE

Parts to Mute

Part 1–Part16,

4&5, 1&4&5,

All except 10,

All except 2&10

Specifies the parts that will be muted by Minus One (p. 73) when playing back an SMF song. Parts for which this setting is

ON will be muted.

Part 1–Part16

: The specified part 1–16 will be muted.

4&5

: Parts 4 and 5 will be muted.

1&4&5

: Parts 1, 4, and 5 will be muted.

All except 10

: Parts other than part 10 will be muted. Normally, only the drums will be heard.

All except 2&10

: Parts other than parts 2 and 10 will be muted.

DBEAM

SETTINGS

D Beam Sens

0–127

This sets the D Beam controller’s sensitivity.

Increasing this value will make the D Beam controller more responsive.

POWER

SAVE

MODE

Time

OFF, 1min, 3min,

5min, 10min,

15min, 20min,

30min, 60min

Amount of idle time that is to pass before the JUNO-Di enters power-save mode.

When the JUNO-Di enters power-save mode, it will reduce its power consumption by turning off the display backlight and

minimizing button illumination.

Item Value Description

JUNO-Di_e.book 76 ページ２００９年６月２２日　月曜日　午前９時２３分

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Roland Juno Di in the language / languages: English as an attachment in your email.

The manual is 13,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Roland Juno Di Manual

Product: