710374
22
Zoom out
Zoom in
Previous page
1/32
Next page
22
System Settings
1. While holding down the [LOAD] button in the right side (R channel) of the browser section, and press the [POWER] switch to turn on the
power.
The DJ-505 is in system setting mode, and the [START/STOP] button of the TR-S section is blinking.
2. Press the TR-S pad or button that corresponds with the setting you want to make.
The display shows the current value.
3. Use the [VALUE] knob to change the value of the setting.
4. When you’ve nished making settings, press the blinking [START/STOP] button.
After a few seconds, the display shows CONp.”
5. Turn the DJ-505’s power o and then on again.
Pad Item Value (Bold: default) Explanation
TR-S pad
[1] Mic audio low cut lter setting
OFF
,
1
10
Adjusts the strength of the low cut lter applied to the mic audio.
1–10 Higher values produce a stronger eect.
OFF The low cut lter is not applied.
[2] Mic audio noise gate setting
OFF
,
1
10
Species the strength of the noise gate applied to the mic audio.
1–10 As the value increases, even higher-level sound will be cut.
OFF The noise gate is not applied.
[3] Mic input eect selection
OFF
,
(Reverb),
dLy
(Delay),
(Delay + Reverb)
Species the eect that is applied to the mic audio.
Reverb Reverb is applied.
Delay Delay is applied.
Delay + Reverb Delay and reverb are applied simultaneously.
OFF No eect is applied.
[4] Mic input eect setting
OFF
,
1
4
10
Adjusts the depth of the eect that is applied to the mic audio.
1–10 Higher values apply the eect more deeply.
OFF No eect is applied.
[5] BOOTH OUT jack setting
On
,
OFF
Species whether the mic audio is output (On) or is not output (OFF) from the BOOTH OUT
jacks.
[6] DVS input selection
PHOn
(PHONO),
Line
(LINE),
(AUX)
Selects the input signal when using DVS.
Phono
The phono-level (a connected turntable without an EQ amp) input is the
source.
Line
The line-level (a connected DJ player or turntable with an EQ amp) is the
source.
Aux
DVS is not used; rather, the input to the INPUT (CH 1, CH 2) jacks is used as
the AUX signal.
[7] EQ ([HI]/[MID]/[LOW] knobs) maximum value
3db
,
6db
Species the maximum value of the equalizer.
When the [HI]/[MID]/[LOW] knobs of each channel are turned all the way to the right, they
have the value specied here.
* This setting is eective only in stand-alone mode.
[8] Master output attenuator level
0
,
-3
,
-6
,
-12
,
-18
(dB)
Species the attenuation level of the master output. The master output level decreases by the
amount of this value.
[9] BOOTH OUT attenuator level
0
,
-3
,
-6
,
-12
,
-18
(dB)
Species the attenuation level of the booth output. The booth output level decreases by the
amount of this value.
[10] Cross fader curve
Line
(Linear),
poU-
(Power)
Species the curve of the cross fader.
left/rightcenter
low
high
Position of fader
Level
Linear Power
* This setting is eective only in stand-alone mode.
[11] Margin at both ends of cross fader
0
,
1
10
Species the margin at both ends of the cross fader. Higher values increase the margin,
providing more play at each end of the cross fader.
[12] Performance pad velocity curve
LoU-
(Low),
Nid
(Mid),
Hi
(Hi)
Species the velocity curve of the performance pads (the way in which the level changes in
response to the strength of your strike on the pad).
strongweak
low
high
Strength of pad strike
Level
Low Mid Hi
[13] TR-S section knob mode
PiccW
(Pick),
JUNP
(Jump)
Species how the knobs in the TR-S section operate.
Pick
If there is a discrepancy between the recalled value and the position of
the knob, data is output only after you turn the knob to the position that
matches the value.
Jump Data is always output according to the position of the knob.
[14] Demo mode time setting
OFF
,
1
10
30
Species the time (minutes) from when the DJ-505 was last operated until it enters demo
mode.
If this is OFF, demo mode will not operate.
[15] LED brightness adjustment
0
3
Adjusts the brightness when a button, pad, or indicator is lit.
Higher values decrease the brightness.
[16] Auto O function (p. 10) setting
On
,
OFF
When no operation has been performed for a certain length of time, the power turns o
automatically. If you don’t want the power to turn o automatically, set this “OFF.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland DJ-505 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland DJ-505 in the language / languages: English as an attachment in your email.

The manual is 4,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland DJ-505

Roland DJ-505 User Manual - German - 32 pages

Roland DJ-505 User Manual - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info