710316
7
Zoom out
Zoom in
Previous page
1/8
Next page
7
Choking
Choking (pinching) the cymbals edge with the hand
immediately after hitting the cymbal makes the sound stop.
To make use of choking play techniques, youll need to
connect to a trigger input jack on the percussion sound
module that accommodates rim shots.
fig.CY07.e
Troubleshooting
Issues Affecting The Overall System
Check these first
Is the trigger type set correctly?
Make the trigger parameter settings for your percussion
sound module (p. 2).
Is a monaural cable being used?
When a monaural cable is used, the sound does not
change when an edge shot or a bell shot is made. Choke
play is not possible, either.
Use stereo cable.
The sound does not change when an edge
shot is made
Is the cable connected to the BOW/EDGE output?
Make the connection to the BOW/EDGE output to enable
the CY-12R/C to support edge shots (p. 5).
Are you striking the cymbal in the area with the edge
sensors?
Edge sensors are embedded only in the part of the CY-
12R/C directly in front (p. 6).
The sound does not change when a bell shot
is made
Is the cable connected to the BOW/BELL output?
Make the connection to the BOW/BELL output to enable
the CY-12R/C to support bell shots (p. 5).
Use the shoulder of the stick when playing bell shots
(p. 6).
Adjust the “Scan Time.”
Choke play is not possible
Are you choking the cymbal in the area with the edge
sensors?
Edge sensors are embedded only in the part of the CY-
12R/C directly in front (p. 7).
Ride cymbal sounds odd
(Other cymbal sound is heard simultaneously)
If using a sound module other than the TD-10 furnished
with the TDW-1 with V-Cymbal Control, connect either
the CY-12R/Cs BOW/BELL output or the BOW/EDGE
output (p. 5).
Double sounding
Are any cables touching the CY-12R/C?
Secure the cables in place with the cable ties so that they
do not touch the units. Also, be careful to make sure that
the cables are not pulled by the movement of a cymbal
when struck (p. 5).
Are the stopper, felt washer, and wing nut attached
correctly?
Double triggering may occur if the stopper and/or wing
nut is loose. Use a tuning key (drum key) to tighten
properly.
* If double triggering still occurs, try adjusting trigger
parameters, such as Retrigger Cancel, on the sound module you
are using (TD-6, TD-8, TD-10, etc.)
The volume level is too low
If the cymbal is struck while power to the drum module
(such as the TD-6, TD-8, or TD-10) is turned on, the
response to light hits will be poor. Do not strike pads or
cymbals while turning on the power.
When using the TD-10 + TDW-1 with V-
Cymbal Control
No sound is heard
Is the trigger type set to “CTR”?
Tones from inputs for which the trigger type is set to
CTR do not sound (p. 6).
The sound does not vary when the striking
position changes
The CY-12R/C is capable of the positional detection
feature. Positional detection is possible when
plugged into the specified input on a Roland sound
module with this feature.
For more on tones that can change according to the
part of the cymbal struck, refer to the tone list in the
Owner's Manual that came with your drum module.
With trigger types RdB and CrB, positional
sensing is not possible. Use RdA or CrA.
Specifications
CY-12R/C: V-Cymbal Ride/Crash
Pad Size: 12 inches
Trigger: 3 (Bow/Bell/Edge)
Dimensions: 300 (W) x 300 (D) x 51 (H)
11-13/16 (W) x 11-13/16 (W) x 2-1/16 (H)
Weight: 1.1 kg
2 lbs 7 oz
Accessories: Owners Manual, Connection Cable,
Wing Nut, Felt Washer, Stopper, Cable Tie
Options: Cymbal Mount (MDY-10U)
Stand (MDS-6, MDS-8, MDS-10)
* In the interest of product improvement, the specifications and/or
appearance of this unit are subject to change without prior notice.
Edge sensor
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland CY-12R-C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland CY-12R-C in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland CY-12R-C

Roland CY-12R-C User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info