710316

Roland CY-12R-C Manual

5
Zoom out
Zoom in
Previous page
1/8
Next page
5
Attaching to a Stand
Attach the CY-12R/C with the optional cymbal mount (MDY
series), or drum stand cymbal mount (MDS series).
1. Use a commercially available drum key to
tighten the stopper bolt.
The stopper keeps the CY-12R/C from turning, and
prevents the cables from catching or getting tangled on the
stand.
fig.01.e
2. Attach the CY-12R/C so the unit is oriented as
shown in the diagram (bolt should be opposite
the output jacks).
3. Tighten the wing nut to obtain the desired
movement.
Use the included felt washer and the wing nut.
fig.02.e
• Double sounding may occur if the wing nut is loose.
• Do not use the washer or felt included with the cymbal
mount (MDY series).
Connecting to
a Percussion Sound Module
(TD-6, TD-8, TD-10, etc.)
About the Output Jacks
The CY-12R/C features two different output jacks, BOW/BELL
and BOW/EDGE.
Use the BOW/BELL output jack when you want to play the
bow and the bell sounds; use the BOW/EDGE output jack
when you want to play the bow and the edge sounds.
Use either the BOW/BELL or BOW/EGDE output jack, but
not both at the same time (except for the TD-10 + TDW-1 with
V-Cymbal Control).
Connecting both jacks results in two separate trigger inputs
playing simultaneously.
If you are using the TD-10 + TDW-1 with V-Cymbal Control,
you can use both the BOW/BELL and BOW/EGDE output
jacks at the same time (Three Way Triggering). For more
details, refer to “If Using TD-10 + TDW-1 with V-Cymbal
Control” (p. 6).
Making the Connections
To prevent malfunction and/or damage to speakers or other
devices, always turn down the volume, and turn off the power
on all devices before making any connections.
1.
Use the included cable to connect one of the CY-
12R/C’s output jacks (either one, but not both,
EXCEPT when using with the TD-10 + TDW-1
with V-Cymbal Control installed) to the drum
sound module’s trigger input jack.
Connect the L-shaped plug of the included cable to the
CY-12R/C. This will prevent strain from being applied to
the CY-12R/C.
To make use of edge shot and choking play techniques,
you'll need to connect to a trigger input jack on the
percussion sound module that accommodates rim shots.
The TD-8's “1/2 (KICK 1/2)” and “11/12 (AUX 1/2)” do
not support rim shots.
2. Secure the cable with cable ties.
Leave enough slack so that the cable is not pulled by any
shaking or vibration of the cymbal when it is struck.
fig.CY03.e
Take care to ensure that the cable does not come into
contact with the cymbal or stand. Contact between the
cable and the cymbal or stand can result in problems,
Stopper
(Be sure to
orient it correctly)
Tighten the bolt with
a commercially available
drum key
Wing Nut
Felt Washer
Output Jack Corresponding Play
Methods
Tones
Sounded
BOW/BELL Bow Shot (p. 6) Head
Bell Shot (p. 6) Rim
Choke (p. 7) –
BOW/EDGE Bow Shot (p. 6) Head
Edge Shot (p. 6) Rim
Choke (p. 7) –
Tighten it
not to slip
Wind the cable
tie twice
Secure the cable in place
with the cable tie
Leave some
slack in
the cable
Turn back
to fix the
cable
Next
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland CY-12R-C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland CY-12R-C in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland CY-12R-C

Roland CY-12R-C User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info