527390

Roland BK-7M BACKING MODULE Manual

121
Zoom out
Zoom in
Previous page
1/128
Next page
MFX types and parameters
Backing Module BK-7m
r
121
76. LoFi Noise
In addition to a lo-fi effect, this adds various types of noise
such as white noise and disc noise.
●
LoFi Type (1, 2, 3, 4, 5, 6, 7, 8, 9)—Degrades the sound quality.
The sound quality grows poorer as this value is increased.
●
Post Filter Type (OFF, LPF, HPF)—Type of filter. OFF: no filter is
used. LPF: cuts the frequency range above the Cutoff value. HPF:
cuts the frequency range below the Cutoff value.
●
Post Filter Cutoff (200~8000, Bypass)—Center frequency of the
filter.
●
W/P Noise Type (White, Pink)—Switch between white noise and
pink noise.
●
W/P Noise LPF (200~8000, Bypass)—Center frequency of the low
pass filter applied to the white/pink noise (BYPASS: no cut).
●
W/P Noise Level (0~127)—Volume of the white/pink noise.
●
Disc Noise Type (LP, EP, SP, RND)—Type of record noise. The fre-
quency at which the noise is heard depends on the selected
type.
●
Disc Noise LPF (200~8000Hz, Bypass)—Adjusts the cutoff fre-
quency of the low pass filter applied to the record noise. If you
don’t want to filter out any high frequencies, set this parameter
to BYPASS.
●
Disc Noise Level (0~127)—Volume of the record noise.
●
Hum Noise Type (50Hz, 60Hz)—Frequency of the hum noise.
●
Hum Noise LPF (200~8000Hz, Bypass)—Center frequency of the
low pass filter applied to the hum noise (BYPASS: no cut).
●
Hum Noise Level (0~127)—Volume of the hum noise.
●
EQ Low Gain (–15dB~0~15dB)—Gain of the low frequency
range.
●
EQ High Gain (–15dB~0~15dB)—Gain of the high frequency
range.
●
Balance (D100:0W, D50:50W, D0:100W)—Volume balance
between the direct (D) and the effect sound (W).
●
Level (0~127)—Output level.
77. LoFi Comp
This is an effect that intentionally degrades the sound quality
for creative purposes.
●
Pre Filter Type (1, 2, 3, 4, 5, 6)—Selects the type of filter applied
to the sound before it passes through the Lo-Fi effect.
●
LoFi Type (1, 2, 3, 4, 5, 6, 7, 8, 9)—Degrades the sound quality.
The sound quality grows poorer as this value is increased.
●
Post Filter Type (OFF, LPF, HPF)—Type of filter. OFF: no filter is
used. LPF: cuts the frequency range above the Cutoff value. HPF:
cuts the frequency range below the Cutoff value.
●
Post Filter Cutoff (200~8000, Bypass)—Basic frequency of the
Post Filter.
●
EQ Low Gain (–15dB~0~15dB)—Gain of the low frequency
range.
●
EQ High Gain (–15dB~0~15dB)—Gain of the high frequency
range.
●
Balance (D100:0W, D50:50W, D0:100W)—Volume balance
between the direct (D) and the effect sound (W).
●
Level (0~127)—Output level.
78. LoFi Radio
In addition to a Lo-Fi effect, this effect also generates radio
noise.
●
LoFi Type (1, 2, 3, 4, 5, 6, 7, 8, 9)—Degrades the sound quality.
The sound quality grows poorer as this value is increased.
●
Post Filter Type (OFF, LPF, HPF)—Type of filter. OFF: no filter is
used. LPF: cuts the frequency range above the Cutoff value. HPF:
cuts the frequency range below the Cutoff value.
●
Post Filter Cutoff (200~8000, Bypass)—Basic frequency of the
Post Filter.
●
Radio Detune (0~127)—Simulates the tuning noise of a radio. As
this value is raised, the tuning drifts further.
●
Radio Noise Level (0~127)—Volume of the radio noise.
●
EQ Low Gain (–15dB~0~15dB)—Gain of the low frequency
range.
●
EQ High Gain (–15dB~0~15dB)—Gain of the high frequency
range.
●
Balance (D100:0W, D50:50W, D0:100W)—Volume balance
between the direct (D) and the effect sound (W).
●
Level (0~127)—Output level.
79. Telephone
This effect simulates the tonal character of a telephone trans-
mission.
●
Voice Quality (0~15)—Audio quality of the telephone voice.
●
Treble (–15dB~0~15dB)—Bandwidth of the telephone voice.
●
Balance (D100:0W, D50:50W, D0:100W)—Volume balance
between the direct (D) and the effect sound (W).
●
Level (0~127)—Output level.
80. Phonograph
Simulates a sound recorded on an analog record and played
back on a record player. This effect also simulates the various
types of noise that are typical of a record and even the rota-
tional irregularities of an old turntable.
●
Signal Distortion (0~127)—Depth of distortion.
●
Frequency Range (0~127)—Frequency response of the playback
system. Decreasing this value will produce the impression of an
old system with a poor frequency response.
●
Disc Type (LP, EP, SP)—Rotational speed of the turntable. This
will affect the frequency of the scratch noise.
●
Scratch Noise Level (0~127)—Amount of noise due to scratches
on the record.
●
Dust Noise Level (0~127)—Volume of noise due to dust on the
record.
●
Hiss Noise Level (0~127)—Volume of continuous “hiss”.
●
Total Noise Level (0~127)—Volume of overall noise.
●
Wow (0~127)—Depth of long-cycle rotational irregularity.
●
Flutter (0~127)—Depth of short-cycle rotational irregularity.
●
Random (0~127)—Depth of indefinite-cycle rotational irregular-
ity.
●
Total Wow/Flutter (0~127)—Depth of overall rotational irregu-
larity.
●
Balance (D100:0W, D50:50W, D0:100W)—Volume balance
between the direct (D) and the effect sound (W).
●
Level (0~127)—Output level.
81. Step Pitch
A pitch shifter in which the amount of pitch shift is varied by a
16-step sequence.
●
Step 1~16 (–24~0~12 semitones)—Amount of pitch shift at each
step (semitone units)
●
Rate [sync] (Hz, Note)—Use this parameter to specify whether
(“Note”) or not (“Hz”) the rate should be synchronized to the
Arranger or Recorder tempo. Depending on your choice, the
setting range of the following parameter refers to a speed (Hz)
or a note value.
●
Rate [Hz] (0.05~10.00Hz)—Rate at which the 16-step sequence
will cycle.
●
Rate [note] (musical notes)—Rate parameters can be set as a
note-value of a tempo if you set the “Sync” parameter above to
“Note”. Specify the value of the desired note.
●
Attack (0~127)—Speed at which the amount of pitch shift
changes between steps.
●
Gate Time (0~127)—Duration of the pitch shifted sound at each
step.
●
Fine (–100~100)—Pitch shift adjustment for all steps (2-cent
units).
●
Delay Time [sync] (msec, Note)—Use this parameter to specify
whether (“Note”) or not (“msec”) the delay time should be syn-
chronized to the Arranger or Recorder tempo. Depending on
your choice, the setting range of the following parameter refers
to a time or a note value.
●
Delay Time [msec] (0~1300ms)—Delay time from the original
sound until the pitch-shifted sound is heard.
●
Delay Time [note] (Musical Notes)—Delay times can be set as a
note-value of a tempo, if you set the “Sync” parameter above to
“Note”. Specify the value of the desired note.
●
Feedback (–98%~0~+98%)—Proportion of the pitch-shifted
sound that is to be returned to the input (negative values invert
the phase).
●
EQ Low Gain (–15dB~0~15dB)—Gain of the low frequency
range.
BK-7m_UK.book Page 121 Tuesday, January 4, 2011 9:25 AM
… 121 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland BK-7M BACKING MODULE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland BK-7M BACKING MODULE in the language / languages: English as an attachment in your email.

The manual is 7,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland BK-7M BACKING MODULE

Roland BK-7M BACKING MODULE Additional guide - English - 10 pages

Roland BK-7M BACKING MODULE Additional guide - German - 10 pages

Roland BK-7M BACKING MODULE User Manual - German - 124 pages

Roland BK-7M BACKING MODULE User Manual - Dutch - 128 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info