Manual Roland BK-7M BACKING MODULE (page 119 of 128) (English)

527390

119

Zoom out

Zoom in

1/128

MFX types and parameters

Backing Module BK-7m

119

●

Delay 1 Time [msec] (0~1300ms)—Delay time from when sound

is input to delay 1 until the delay sound is heard.

●

Delay 1 Time [note] (musical notes)—Delay times can be set as a

note-value of a tempo, if you set the “Sync” parameter above to

“Note”. Specify the value of the desired note.

●

Delay 1 Feedback (–98%~0~+98%)—Proportion of the delay

sound that is to be returned to the input of delay 1 (negative

values invert the phase).

●

Delay 1 HF Damp (200~8000Hz, Bypass)—Frequency at which

the high-frequency content of the delayed sound of delay 1 will

be cut (BYPASS: no cut).

●

Delay 2 Time [sync] (msec, Note)—Use this parameter to specify

whether (“Note”) or not (“msec”) the delay 2 time should be

synchronized to the Arranger or Recorder tempo. Depending on

your choice, the setting range of the following parameter refers

to a time (msec) or a note value.

●

Delay 2 Time [msec] (0~1300ms)—Delay time from when sound

is input to delay 2 until the delay sound is heard.

●

Delay 2 Time [note] (musical notes)—Delay times can be set as a

note-value of a tempo, if you set the “Sync” parameter above to

“Note”. Specify the value of the desired note.

●

Delay 2 Feedback (–98%~0~+98%)—Proportion of the delay

sound that is to be returned to the input of delay 2 (negative

values invert the phase).

●

Delay 2 HF Damp (200~8000Hz, Bypass)—Frequency at which

the high-frequency content of the delayed sound of delay 2 will

be cut (BYPASS: no cut).

●

Panpot (L64~0~63R)—Stereo location of the output sound. This

is a mono effect that combines incoming signals. You can, how-

ever, place the processed signal anywhere between the left and

right channels.

●

EQ Low Gain (–15dB~0~15dB)—Gain of the low frequency

range.

●

EQ High Gain (–15dB~0~15dB)—Gain of the high frequency

range.

●

Balance (D100:0W, D50:50W, D0:100W)—Volume balance

between the direct (D) and the effect sound (W).

●

Level (0~127)—Output level.

70. MLT Tap DLY

This effect provides four delays. Each of the Delay Time param-

eters can be set to a note length based on the selected tempo.

You can also set the panning and level of each delay sound.

●

Delay Time 1~4 [sync] (msec, Note)—Use this parameter to spec-

ify whether (“Note”) or not (“msec”) the delay time should be

synchronized to the Arranger or Recorder tempo. Depending on

your choice, the setting range of the following parameter refers

to a time or a note value.

●

Delay 1~4 Time [msec] (0~2600ms)—Adjusts the time until

Delay 1~4 are heard.

●

Delay 1~4 Time [note] (musical notes)—Delay times can be set

as a note-value of a tempo, if you set the “Sync” parameter

above to “Note”. Specify the value of the desired note.

●

Delay 1 Feedback (–98%~0~+98%)—Adjusts the amount of the

delay sound that’s fed back into the effect. Negative (–) settings

invert the phase.

●

HF Damp (200~8000Hz, Bypass)—Adjusts the frequency above

which sound fed back to the effect is ﬁltered out. If you don’t

want to ﬁlter out any high frequencies, set this parameter to

BYPASS.

●

Delay 1~4 Panpot (L64~0~63R)—Stereo location of Delays 1~4.

●

Delay 1~4 Level (0~127)—Output level of Delays 1~4.

●

EQ Low Gain (–15dB~0~15dB)—Gain of the low frequency

range.

●

EQ High Gain (–15dB~0~15dB)—Gain of the high frequency

range.

●

Balance (D100:0W, D50:50W, D0:100W)—Volume balance

between the direct (D) and the effect sound (W).

●

Level (0~127)—Output level.

71. Reverse DLY

This is a reverse delay that adds a reversed and delayed sound

to the input sound. A tap delay is connected immediately after

the reverse delay.

●

Threshold (0~127)—Volume at which the reverse delay will

begin to be applied.

●

Rev Delay Time [sync] (msec, Note)—Use this parameter to spec-

ify whether (“Note”) or not (“msec”) the reverse delay time

should be synchronized to the Arranger or Recorder tempo.

Depending on your choice, the setting range of the following

parameter refers to a time (msec) or a note value.

●

Rev Delay Time [msec] (0~1300ms)—Delay time from when

sound is input into the reverse delay until the delay sound is

heard.

●

Rev Delay Time [note] (musical notes)—Delay times can be set

as a note-value of a tempo, if you set the “Sync” parameter

above to “Note”. Specify the value of the desired note.

●

Rev Delay Feedback (–98%~0~+98%)—Proportion of the delay

sound that is to be returned to the input of the reverse delay

(negative values invert the phase)

●

Rev Delay HF Damp (200~8000Hz, Bypass)—Frequency at which

the high-frequency content of the reverse-delayed sound will be

cut (BYPASS: no cut).

●

Rev Delay Panpot (L64~0~63R)—Panning of the reverse delay

sound.

●

Rev Delay Level (0~127)—Volume of the reverse delay sound.

●

Delay 1 Time [sync] (msec, Note)

●

Delay 2 Time [sync] (msec, Note)

●

Delay 3 Time [sync] (msec, Note)—Use this parameter to specify

whether (“Note”) or not (“msec”) the delay time should be syn-

chronized to the Arranger or Recorder tempo. Depending on

your choice, the setting range of the following parameter refers

to a time or a note value.

●

Delay 1 Time [msec] (0~1300ms)

●

Delay 2 Time [msec] (0~1300ms)

●

Delay 3 Time [msec] (0~1300ms)—Adjusts the time until the

delay is heard.

●

Delay 1 Time [note] (musical notes)

●

Delay 2 Time [note] (musical notes)

●

Delay 3 Time [note] (musical notes)—Delay times can be set as a

note-value of a tempo, if you set the “Sync” parameter above to

“Note”. Specify the value of the desired note.

●

Delay 3 Feedback (–98%~0~+98%)—Proportion of the delay

sound that is to be returned to the input of the tap delay (nega-

tive values invert the phase).

●

Delay HF Damp (200~8000Hz, Bypass)—Frequency at which the

low-frequency content of the tap delay sound will be cut

(BYPASS: no cut).

●

Delay 1 Panpot (L64~0~63R)

●

Delay 2 Panpot (L64~0~63R)—Panning of the tap delay sounds.

●

Delay 1 Level (0~127)

●

Delay 2 Level (0~127)—Volume of the tap delay sounds.

●

EQ Low Gain (–15dB~0~15dB)—Gain of the low frequency

range.

●

EQ High Gain (–15dB~0~15dB)—Gain of the high frequency

range.

●

Balance (D100:0W, D50:50W, D0:100W)—Volume balance

between the direct (D) and the effect sound (W).

●

Level (0~127)—Output level.

72. Shuffle DLY

Adds a shufﬂe to the delay sound, giving the sound a bouncy

delay effect with a swing feel.

●

Delay Time [sync] (msec, Note)—Use this parameter to specify

whether (“Note”) or not (“msec”) the delay time should be syn-

chronized to the Arranger or Recorder tempo. Depending on

your choice, the setting range of the following parameter refers

to a time or a note value.

●

Delay Time [msec] (0~2600ms)—Adjusts the time until the delay

is heard.

●

Delay Time [note] (Musical Notes)—Delay times can be set as a

note-value of a tempo, if you set the “Sync” parameter above to

“Note”. Specify the value of the desired note.

BK-7m_UK.book Page 119 Tuesday, January 4, 2011 9:25 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Roland BK-7M BACKING MODULE in the language / languages: English as an attachment in your email.

The manual is 7,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Roland BK-7M BACKING MODULE

Roland BK-7M BACKING MODULE Additional guide - English - 10 pages

Roland BK-7M BACKING MODULE Additional guide - German - 10 pages

Roland BK-7M BACKING MODULE User Manual - German - 124 pages

Roland BK-7M BACKING MODULE User Manual - Dutch - 128 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Roland BK-7M BACKING MODULE Manual

Product: