708869
60
Zoom out
Zoom in
Previous page
1/72
Next page
60
MIDI Implementation
2. Transmitted data (Media Player Section)
2.1 Transmitted messages while a phrase
is being played back
The stored MIDI message are transmitted When the MIDI phrase will playback after OUT is
set in the MIDI OUT.
In this case, AR-200/3000 is not transmitted MIDI messages which are received.
2.2 Transmitted message which are received.
When THRU is set in the MIDI OUT, AR-200/3000 transmits message which are received.
2.3
Transmitted message which are produced.
When OUT is set in the MIDI OUT, AR-200/3000 transmits the following produced
messages.
Channel Voice Message
Note Off
Status Second Third
8nH kkH 40H
n = MIDI Channel No.: 0H -- FH (ch.1--ch.16)
kk = Note No.: 00H--7FH (0--127)
* After the MIDI Phrase is stopped, AR-200/3000 produces Note off message for received
notes remains on.
* When Note On is sent at the start of an audio performance, the same note number as that
of the Note On is transmitted. For more information about sending notes, refer to the
Note On section below.
Note ON
Status
Second Third
9nH kkH 7FH
n = MIDI Channel No.: 0H--FH (ch.1--ch.16)
kk = Note No.: 00H--7FH (0--127)
* At the start of the audio phrase performance, the note number defined in the MIDI note
map is sent.In this instance, if multiple note numbers are selected in the phrase, only the
lowest note number is transmitted.
* There is no transmission when the Note Send setting is set to "OFF" (Note Send settings
are available only with the AR-3000).
* Data is not output if the MIDI Receive channel setting is "OFF." When set to 1-16, data is
transmitted only on the selected channel. When set to ALL, data is transmitted on
Channel 1.
* There is no transmission during playback of MIDI phrases.
Control Change
Hold1 OFF
Status Second Third
BnH 40H 00H
n = MIDI Channel No.: 0H--FH (ch.1--ch.16)
* *After the MIDI Phrase is stopped, AR-200/3000 produces Note off message for received
notes remains on.
Channel Mode Message
All Note Off (Controller No. 1 2 3)
Status
Second Third
BnH 7BH 00H
n = MIDI channel No.: 0H--FH (ch.1--ch.16)
* Transmitted message while a phrase is being played back.
2.4 Recognized message for sync
System Realtime Message
Timing Clock
status
F8H
* Transmitted message while a phrase is being played back.
Start
status
FAH
Stop
status
FCH
System Common Message
Quarter Frame
* This is transmitted when Sync Out is set to "MTC." The time count transmitted is the
time with the start of the song set to "00h00m00s00f00" with the "MTC Offset" and the
"Delay Time" added.
* MIDI phrases and pattern phrases are not transmitted when Dual Mono mode is
selected.
status
second
F1H mmH (= 0nnndddd)
Regarding the Quarter Frame, please refer to "Receive data (Media Player Section) ~Quarter
Frame~".
System Exclusive Message
MIDI Time Code
Full Message
* This is transmitted when Sync Out is set to "MTC" and the location of the phrase is
moved. The time count transmitted is the time with the start of the song set to
"00h00m00s00f00," and the "MTC Offset" and the "Delay Time" added.
* MIDI phrases and pattern phrases are not transmitted when Dual Mono mode is
selected.
Status Data Bytes Status
F0H 7FH, dev, 01H, 01H F7H
hrH, mnH, scH, frH
Regarding the MIDI Time Code, please refer to "Receive data (Media Player Section) ~MIDI
Time Code~".
MIDI Machine Control (MMC)
* Data is transmitted when MMC mode is set to "MASTER."
STOP (MCS)
Status
Data Bytes Status
F0H 7FH, dev, 06H, 01H F7H
Byte Description
F0H Status of System Exclusive Message
7FH Universal System Exclusive Message Real time Header
dev device ID
06H MMC Command Message
01H STOP (MCS)
F7H EOX (End of System Exclusive Message)
* When "STOP" is pressed, a Device ID of 7FH is transmitted.
DEFERRED PLAY (MCS)
Status Data Bytes Status
F0H 7FH, dev, 06H, 01H F7H
Byte Description
F0H Status of System Exclusive Message
7FH Universal System Exclusive Message Real time Header
dev device ID (or 7FH)
06H MMC Command Message
03H DEFERRED PLAY (MCS)
F7H EOX (End of System Exclusive Message)
* When "START" is pressed, a Device ID of 7FH is transmitted.
RECORD STROBE (MCS)
Status Data Bytes Status
F0H 7FH, dev, 06H, 07H F7H
Byte Description
F0H Status of System Exclusive Message
7FH Universal System Exclusive Message Real time Header
7FH device ID (or 7FH)
06H MMC Command Message
06H RECORD STROBE (MCS)
F7H EOX (End of System Exclusive Message)
* When recording of a phrase begins, a Device ID of 7FH is transmitted.
RECORD EXIT (MCS)
Status Data Bytes Status
F0H 7FH, dev, 06H, 07H F7H
Byte Description
F0H Status of System Exclusive Message
7FH Universal System Exclusive Message Real time Header
dev device ID
06H MMC Command Message
07H RECORD EXIT
F7H EOX (End of System Exclusive Message)
* When recording of a phrase is stopped, a Device ID of 7FH is transmitted
AR-200_e.book 60 ページ 2003年7月14日 月曜日 午後1時11分
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland AR-200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland AR-200 in the language / languages: English as an attachment in your email.

The manual is 2,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info