622366

Roland ADA-7000 Manual

16
Zoom out
Zoom in
Previous page
1/24
Next page
16
Supplementary Notes
How to connect the VM-7000 series and the
ADA-7000
To connect the VM-7200/7100 and the ADA-7000 via R-BUS, VM-24E I/O Expansion Board (sold separately) is
needed. By installing the VM-24E to a VM-7200/7100 processor, you can connect up to three ADA-7000’s.
* Refer to VM-7200/7100 Owner’s Manual p. 14 “Installing
R-BUS (RMDB2) Connectors (VM-24E).”
Connection
Connect the VM-7200/7100 and the ADA-7000 with the
R-BUS cable attached in the ADA-7000 box.
* Refer to ADA-7000 Owner’s Manual p. 9 “An Example of Connection.”
Booting up
Turn the power on the ADA-7000 first, then VM-7200/7100 processor, and finally VM-C7200/C7100 console.
Clock source setting
If clock source has not been set, noise may be generated from the audio output on the ADA-7000 and the VM-7000.
While setting the clock source, please turn down the master and monitor level, and turn up again after the setting is
finished. Set the sampling clock on the ADA-7000 and the VM-7000 as follows.
Clock Source on the ADA-7000
connected to the R-BUS (1–8): R-BUS
Clock Source on the ADA-7000
connected to the R-BUS (9–16): R-BUS
Clock Source on the ADA-7000
connected to the R-BUS (17–24): R-BUS
Master clock on the VM-7000: INTERNAL
ADA-7000 setting
Check if the clock source on the ADA-7000 is set to R-BUS. When the ADA-7000 is booted up, the clock source is set
to R-BUS. If you connect multiple ADA-7000, set the clock source on all ADA-7000 to R-BUS.
* Refer to ADA-7000 Owner’s Manual p. 6 “Clock source.”
VM-7000 setting
Set the master clock of the VM-7200/7100 to INTERNAL as follows.
1. Hold down [SHIFT], and press [PROJECT].
2. Press [DOWN] cursor, then [F1 (DIGITAL I/O)].
3. Select “WORD CLOCK SOURCE,” and set it to “INTERNAL” with V1 knob, then press [F1 (SET)] to activate the result.
* Refer to VM-C7200/C7100 Owner’s Manual p. 32 “Checking the overall system.”
* If you set the clock source differently, please refer to the
ADA-7000 Owner’s Manual p. 6 “Clock source” and the
VM-C7200/C7100 Owner’s Manual p. 31 “About Digital Connections and the Master Clock.”
*VM-7000 is not accommodated with 96.0 kHz sample rate. 96.0 kHz sample rate capability on the ADA-7000 is for
the future devices.
* If the system of the VM-C7200/C7100 is version 1.0x,
“DIF-AT” is displayed in the R-BUS CONFIG page even though the ADA-7000 is connected. This cause no problem
for the operation. With the VM-C7200/C7100 version 1.10 or later, you can set the ADA-7000 with the R-BUS
CONFIG page.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Roland ADA-7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Roland ADA-7000 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info