168917

Rodek rn 1600 Manual

28
Zoom out
Zoom in
Previous page
1/32
Next page
28
5. CROSSOVER SETTINGS
5.3 BANDPASS FOR KICKBASS
SYSTEMS
If you intend to operate a kick bass loudspeaker system in the
front doors of your vehicle, you must select two crossover fre-
quencies at the active crossover of your RODEK amplifier. The
operation mode must be set to band pass. The band pass filter
contains a high pass with a cascaded low pass filter. The low
pass crossover point is usually set at a frequency that equals
approx. twice the value of the high pass crossover setting. The
low pass filter is mostly set a little lower, than the high pass
crossover frequency setting of the satellite channel.
Kickbass speaker system, front door mounted,
recommended band pass frequencies:
16 cm Kickbass Speaker System 80 – 110 Hz High pass
150 – 200 Hz Low pass
5.4 BANDPASS FOR SUBWOOFER
SYSTEMS
To drive a subwoofer system, the integrated electronic crossover
must also operate in band pass mode. Before you attempt to
adjust the low pass crossover frequency, you must first turn the
(subsonic) high pass frequency control counterclockwise to its
lowest position at 10 Hz.
Now you can set an appropriate low pass crossover frequency.
For this purpose, open the input gain control – the arrow of the
knob should point to “noon” – so you can hear the subwoofer
playing. Ideally, the low pass cut-off frequency should be set
between 50 to 90 Hz – and this setting has to be entirely deter-
mined by ear. Try to find low pass crossover frequency setting,
that gives you a “full-bodied” bass reproduction with enough
impact in the upper bass range.
Note: If the low pass crossover frequency is set too low, the
sound will have a tendency to sound extremely soft and low-
end heavy!
Now you can adjust the subsonic high pass, if you wish to squee-
ze out the most (max-dB) of your subwoofer system. Turn the
high pass frequency control up, to a point where you can hear
that the bass reproduction starts to get “thinner”. The subsonic
high pass frequency should be set to a value between 20 to
maximum 50 Hz.
NC-Amp 1-2-4-5-CH Manual_D+E_pfade.indd 28 09.05.2009 11:25:33 Uhr
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Rodek rn 1600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Rodek rn 1600 in the language / languages: English, German as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info