512484

Robomow Tuscania 500 Manual

96
Zoom out
Zoom in
Previous page
1/268
Next page
EN
42
4.2 Other Operational or Fault Problems
Problem
Encountered
Probable Cause/Event Corrective/User Action
- Confirm that the time in the mower is
set correctly (hour and date)
- Set the time (See paragraph 2.2.2)
Robomow operates
at the wrong times
- The ‘GO’ button was pressed with no
meaning, by someone or by a pet (‘Last
stop cause’ under the ‘Information’
menu should be 805).
- To prevent unintended operation you can
activate the ‘Child guard’ option, which
requires pressing of few buttons in order to
start the operation.
- Low battery voltage
- Rain detected at the scheduled time
- Some obstacle is stuck or wrapped
around the blade prevent it rotating.
- Signal problem
- In general, whenever Robomow does not
start the operation at the scheduled time,
the cause is recorded under ‘Program
Display’ (refer to end of 2.1.1 for more
details).
Robomow has
skipped the
scheduled operation
- The program was set to ‘off’ – the main
display shows ‘Mow Zone: Base’ and
not the time and the next start details.
- Change the setting of the ‘Program’ to ‘on’
- Wire disconnected from perimeter
switch or from the Base Station.
- Confirm wire is plugged in and wire leads
are firmly attached.
- Perimeter wire cut
- Walk along perimeter, including islands and
look for obvious cuts or breaks in the wire.
Repair with Robomow wire splice
connectors.
'Cut wire’ indicator
flashing on
Perimeter Switch
or
the Base Station
beeps continuously
for 'Cut wire’
- Poor connections
- Check and repair all loose/poor or corroded
connections.
- Twisted cables, or a screw terminal,
insulated with insulation tape is not a
satisfactory splice. Soil moisture causes
the conductors to oxidize and after a
while result in broken circuit.
- Use the connectors supplied in the box. It is
waterproof and gives a reliable electrical
connection.
‘Poor connection’
indicator flashing on
Perimeter Switch
or
the Base Station
beeps intermittently
for poor wire
splicing or too long
wire
- Perimeter wire too long for one zone
- A maximum perimeter wire length of 500 m
is recommended. Areas requiring longer
lengths should be broken into separate
zones.
- Mower is in deep sleep.
- If not connected to the Base
Station/charger at all times when not in
use, the Robomow will conserve power by
entering into a deep sleep mode. Press the
main switch button (on/off) 3 seconds
continuously to wake Robomow or remove
the fuse for 3 seconds.
Robomow will not
operate and nothing
will display on the
LCD screen.
- Batteries have been discharged from
lack of charge maintenance.
- It is required for the charger to remain
connected to Robomow when not in use.
Failure to do so can cause permanent
damage to the batteries. Contact your
service provider.
The Robomow is
noisy and vibrates
- Damaged or unbalanced blade
- Check the lawn is free from branches,
stones or other objects that can damage
the blade before operating the Robomow.
- Replace the blade
… 96 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow Tuscania 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow Tuscania 500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info